Vectra Genisys Service Manual - DJO Global

More documents

Recommendations

Info

5- TROUBLESHOOTING5.9 PREMODULATED MODE TESTSet up System per 5.6 parts A and B prior toperforming test.A. Premodulated Mode Test Procedures1. Set Scope; Time- 2.50 mS, Channel- 20 V, andTrigger- DC.2. Press Electrotherapy Button.3. Press IFC Premodulated (2p) Button.4. Rotate Intensity Control clockwise until 50is displayed.5. Press “Start”.6. Compare waveform form on scope toFigure 5.7.7. Press Stop. Then press Home Button andmove scope probes to Channel 2 and repeatsteps 2 through 6. Repeat test on channels3 and 4 on 4 Channel Systems.B. Premodulated Mode Test Results1. Waveform is the same between scope andFigure 5.7.Unit passed test.2. No waveform or considerably differentwaveform.Unit failed test. Replace appropriate StimBoard.Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy SystemsFIGURE 5.743
5- TROUBLESHOOTING5.10 RUSSIAN MODE TESTSet up System per 5.6 parts A and B prior toperforming test.A. Russian Mode Test Procedures1. Set Scope; Time- 5 mS, Channel- 50 V, andTrigger- DC.NOTE:A test of the Optional Patient Interrrupt Switchis provided within the Russian Mode Test. Ifyou do not have the Optional Patient InterruptSwitch, skip steps 2, and 11.2.3.4.5.6.7.8.9.10.11.12.Install Patient Interrupt Switch. SeeFigure 5.8.Press Electrotherapy Button.Press Russian Button. Press Edit Button.Press Channel Mode until Co-Contract isdisplayed.Press the Cycle Time Button untilContinuous is displayed.Rotate Therapy Intensity Control clockwiseuntil 100 is displayed.Press “Start”.Compare waveform on scope toFigure 5.9.Verify that both Channels reach 100.Press Patient Interrupt Switch. Verifytreatment stops and “Patient Switch forCh 1 and 2 was pressed. Press any buttonto continue...” message appears. SeeFigure 5.9A. Press any button.Press Stop Button. Press Home Button andmove scope probes to Channel 3 and 4on 4 Channel Systems. Repeat steps 2through 11.B. Russian Mode Test Results1.2.3.4.Waveform is the same between scopeand Figure 5.9, amplitude reached 100and patient switch message displayedwhen switch pressed. See Figure 5.9A.Unit passed test.No waveform or considerably differentwaveform.Unit failed test. Replace appropriate StimBoard.Amplitude failed to reach 100 on bothChannels.Unit failed test. Replace appropriate StimBoard.Patient Switch message did not displaywhen patient switch pressed.(Optional Patient Switch present)Unit failed test.a) Try a known good Patient Switch andrepeat test.b) Replace appropriate Stim Board.Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy SystemsFIGURE 5.8FIGURE 5.9FIGURE 5.9A44
Page 1: ®MovingRehabilitationForwardTherap
Page 7 and 8: 1- THEORY OF OPERATIONVectra Genisy
Page 9 and 10: 2- SAFETY PRECAUTIONS2.1 PRECAUTION
Page 11 and 12: 2- SAFETY PRECAUTIONS2.2 PRECAUTION
Page 13 and 14: 3- NOMENCLATUREVectra Genisys®/Int
Page 23 and 24: 4- SPECIFICATIONSThe specifications
Page 25 and 26: 4- SPECIFICATIONSVectra Genisys®/I
Page 35 and 36: 5- TROUBLESHOOTING5.1 THERAPY SYSTE
Page 37 and 38: 5- TROUBLESHOOTINGVectra Genisys®/
Page 47: 5- TROUBLESHOOTING5.8 INTERFERENTIA
Page 51 and 52: 5- TROUBLESHOOTING5.12 HIGH VOLTAGE
Page 55 and 56: 5- TROUBLESHOOTING5.16 ULTRASOUND A
Page 57 and 58: 5- TROUBLESHOOTING5.18 COMBO OPERAT
Page 61 and 62: 5- TROUBLESHOOTING5.19 SEMG AND SEM
Page 63 and 64: 5- TROUBLESHOOTING5.20 NIMH BATTERY
Page 65 and 66: 6- REMOVAL/REPLACEMENT6.1 CHANNEL 3
Page 67 and 68: 6- REMOVAL/REPLACEMENTVectra Genisy
Page 71 and 72: 6- REMOVAL/REPLACEMENT6.3 THERAPY S
Page 85 and 86: 8- ULTRASOUND CALIBRATION8.1 GENERA
Page 87 and 88: 9- PARTSVectra Genisys®/Intelect L
Page 89 and 90: 9- PARTSTOP HOUSING ASSEMBLY7 - 7AV
Page 91 and 92: 9- PARTSVectra Genisys®/Intelect L
Page 93 and 94: 10- SCHEMATICSVectra Genisys®/Inte
Page 99 and 100:
10- SCHEMATICSVectra Genisys®/Inte
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
11- WARRANTYVectra Genisys®/Intele
show all

Vectra Genisys Service Manual - DJO Global

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?