Vectra Genisys Service Manual - DJO Global

More documents

Recommendations

Info

5- TROUBLESHOOTINGVectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy Systems5.11 MICROCURRENT MODE TESTNOTE:This test does not apply to the Intelect Vet TherapySystem.Set up System per 5.6 parts A and B prior toperforming test.Place ESTI-2 Load Switch in the 10 K Micro positiononly for the Microcurrent Mode Tests. See Figure 5.10.A. Microcurrent Mode Test Procedures1. Set Scope; Time- 250 μS, Channel- 5.0 V,and Trigger- DC.2. Press Electrotherapy Button.3. Press Microcurrent Button and press EditButton.4. Press Frequency Button.5. Press the Up Arrow Button until 1000.0 Hzis displayed.6. Press the Accept and Return Arrow.NOTE:1000.0 Hz should be displayed withinthe Frequency icon. If not, repeat steps 4through 6.7. Press “Polarity” until “Alternating” appearswithin the Polarity icon.NOTE:The Frequency value will continue toramp and rotate due to AlternatingPolarity being selected. This is normal.8. Rotate Therapy Intensity Control until1000 is displayed.9. Press “Start”.10. Compare waveform on scope to Figure5.11 and Figure 5.11A.NOTE:The output will alternate between positiveand negative on the scope.11. Press Stop Button and then press HomeButton.12. Select the next channel to be tested bypressing the Select Channel Button untilthe desired channel is selected. Repeatsteps 2 through 11 for each channel.B. MicroCurrent Mode Test Results1. Waveform is the same between scopeand Figure 5.11 and Figure 5.11A.Unit passed test.2. No waveform or considerably differentwaveform.Unit failed test. Replace appropriate StimBoard.LOAD SWITCHTO 10K MICROFIGURE 5.10PROPER POSITIVE (+) “MICROCURRENT” WAVEFORMSPEC: 10 V PEAK TO PEAK ±10%FIGURE 5.11PROPER NEGATIVE (-) “MICROCURRENT” WAVEFORMSPEC: 10 V PEAK TO PEAK ±10%FIGURE 5.11A45
5- TROUBLESHOOTING5.12 HIGH VOLTAGE PULSED CURRENT(HVPC) MODE TESTSet up Unit per 5.6 parts A and B prior to performingtests.A. High Voltage Pulsed Current (HVPC) ModeTest Procedures1.2.3.4.5.6.7.8.9.10.11.Set Scope; Time- 25 μS, Channel- 50 V, andTrigger- DC.Press Electrotherapy Button.Press High Volt Button.Rotate Therapy Intensity Control clockwiseuntil 250 Volts is displayed.Press Start Button.Compare waveform on scope to Figure5.12.Press Edit Button.Press Polarity Button until Positive isdisplayed in Polarity icon.Compare waveform form on scope toFigure 5.13.Press Display Button until Peak Current isdisplayed in the Display icon.The numbers displayed for amplitudemust not exceed 1.5 Amps. See Figure5.14.Press “Stop”.12.B. High Voltage Pulsed Current (HVPC) ModeTest Results1. Waveforms on scope the same as Figures5.12 and 5.13 and Amps do notexceed 1.5.Unit passed test.2. No waveform or considerably differentwaveforms.Unit failed test. Replace appropriate StimBoard.3. Amps exceed 1.5.Unit failed test. Replace appropriate StimBoard.AMPS MUST NOTEXCEED 1.5Vectra Genisys®/Intelect Legend XT®/ Intelect® Vet Therapy SystemsPROPER NEGATIVE HIGH VOLT WAVEFORMFIGURE 5.12PROPER POSITIVE HIGH VOLT WAVEFORMFIGURE 5.13FIGURE 5.1446
Page 1: ®MovingRehabilitationForwardTherap
Page 7 and 8: 1- THEORY OF OPERATIONVectra Genisy
Page 9 and 10: 2- SAFETY PRECAUTIONS2.1 PRECAUTION
Page 11 and 12: 2- SAFETY PRECAUTIONS2.2 PRECAUTION
Page 13 and 14: 3- NOMENCLATUREVectra Genisys®/Int
Page 23 and 24: 4- SPECIFICATIONSThe specifications
Page 25 and 26: 4- SPECIFICATIONSVectra Genisys®/I
Page 35 and 36: 5- TROUBLESHOOTING5.1 THERAPY SYSTE
Page 37 and 38: 5- TROUBLESHOOTINGVectra Genisys®/
Page 47 and 48: 5- TROUBLESHOOTING5.8 INTERFERENTIA
Page 49: 5- TROUBLESHOOTING5.10 RUSSIAN MODE
Page 55 and 56: 5- TROUBLESHOOTING5.16 ULTRASOUND A
Page 57 and 58: 5- TROUBLESHOOTING5.18 COMBO OPERAT
Page 61 and 62: 5- TROUBLESHOOTING5.19 SEMG AND SEM
Page 63 and 64: 5- TROUBLESHOOTING5.20 NIMH BATTERY
Page 65 and 66: 6- REMOVAL/REPLACEMENT6.1 CHANNEL 3
Page 67 and 68: 6- REMOVAL/REPLACEMENTVectra Genisy
Page 71 and 72: 6- REMOVAL/REPLACEMENT6.3 THERAPY S
Page 85 and 86: 8- ULTRASOUND CALIBRATION8.1 GENERA
Page 87 and 88: 9- PARTSVectra Genisys®/Intelect L
Page 89 and 90: 9- PARTSTOP HOUSING ASSEMBLY7 - 7AV
Page 91 and 92: 9- PARTSVectra Genisys®/Intelect L
Page 93 and 94: 10- SCHEMATICSVectra Genisys®/Inte
Page 101 and 102:
10- SCHEMATICSVectra Genisys®/Inte
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
11- WARRANTYVectra Genisys®/Intele
show all

Vectra Genisys Service Manual - DJO Global

Create successful ePaper yourself

Delete template?

Save as template?