ANNEX I Schedule of Brunei Darussalam Headnote ... - SICE

Annex I: New Zealand's Tariff ScheduleCodeDescriptionBaseEnd2006 2007 2008 2009 2010 2011 2012 2013 2014 2015Ratedate7208.40.90 -- Other 5 5 5 5 5 free 2010- Other, not in coils, not further worked than hot-rolled:7208.51 -- Of a thickness exceeding 10 mm:7208.51.10 --- Rolled on four faces or in a closed box pass, of a width not exceeding 1,250mm, without patterns in relief and having a minimum yield point 5 5 5 5 5 free 2010of other than 355 Mpa--- Other:7208.51.50 ---- Of a width exceeding 1.95 m free free 20067208.51.90 ---- Other 5 5 5 5 5 free 20107208.52 -- Of a thickness of 4.75 mm or more but not exceeding 10 mm7208.52.10 --- Rolled on four faces or in a closed box pass, of a width not exceeding 1,250mm, without patterns in relief and having a minimum yield point 5 5 5 5 5 free 2010of other than 355 Mpa--- Other:7208.52.50 ---- Of a width exceeding 1.95 m free free 20067208.52.90 ---- Other 5 5 5 5 5 free 20107208.53 -- Of a thickness of 3 mm or more but less than 4.75 mm:7208.53.10 --- Rolled on four faces or in a closed box pass, of a width not exceeding 1,250mm, without patterns in relief and having a minimum yield point 5 5 5 5 5 free 2010of other than 355 Mpa7208.53.90 --- Other 5 5 5 5 5 free 20107208.54.00 -- Of a thickness of less than 3 mm 5 5 5 5 5 free 20107208.90 - Other:-- 3 mm or more in thickness:7208.90.02 --- Of a width exceeding 1.95 m and of a thickness exceeding 4.75mm free free 20067208.90.05 --- Other 5 5 5 5 5 free 20107208.90.09 -- Less than 3 mm in thickness 5 5 5 5 5 free 201072.09 Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated:- In coils, not further worked than cold-rolled (cold-reduced):7209.15.00 -- Of a thickness of 3 mm or more 5 5 5 5 5 free 20107209.16.00 -- Of a thickness exceeding 1 mm but less than 3 mm 5 5 5 5 5 free 20107209.17.00 -- Of a thickness of 0.5 mm or more but not exceeding 1 mm 5 5 5 5 5 free 20107209.18.00 -- Of a thickness of less than 0.5 mm 5 5 5 5 5 free 2010- Not in coils, not further worked than cold-rolled (cold reduced):7209.25.00 -- Of a thickness of 3 mm or more 5 5 5 5 5 free 20107209.26.00 -- Of a thickness exceeding 1 mm but less than 3 mm 5 5 5 5 5 free 20107209.27.00 -- Of a thickness of 0.5 mm or more but not exceeding 1 mm 5 5 5 5 5 free 20107209.28.00 -- Of a thickness of less than 0.5 mm 5 5 5 5 5 free 20107209.90.00 - Other free free 200672.10 Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated:- Plated or coated with tin:7210.11.00 -- Of a thickness of 0.5 mm or more free free 20067210.12.00 -- Of a thickness of less than 0.5 mm free free 20067210.20.00 - Plated or coated with lead, including terne-plate free free 20067210.30 - Electrolytically plated or coated with zinc:-- Exceeding 1.6 mm in thickness:7210.30.10 --- Coiled 5 5 5 5 5 free 20107210.30.20 --- Other 5 5 5 5 5 free 2010-- Other:7210.30.30 --- Worked 5 4 4 4 4 free 2010--- Other:7210.30.40 ---- Coiled 5 5 5 5 5 free 20107210.30.90 ---- Other 5 5 5 5 5 free 2010- Otherwise plated or coated with zinc:7210.41.00 -- Corrugated 5 4 4 4 4 free 20101-NZ-147