SK200-UM-251 - Graphtec

More documents

Recommendations

Info

8. DISASSEMBLING AND ADJUSTING THE MECHANICAL PARTS8.2 Left Side CoverDetaching the left side cover(1) Detach the top cover (see Section 8.1).(2) Remove the two M4L8 TP screws on the left side of the scanner unit.(3) Detach the left side cover.Left side coverM4L8 TP screwNote:There is a positioning pillar inside the left side cover.Do not twist the cover when removing the cover.Otherwise, you will break the positioning pillar.Reattaching the left side cover(1) Reattach the left side cover in the reverse order in which it was detached.SK200-UM-251-9370 8-2
8. DISASSEMBLING AND ADJUSTING THE MECHANICAL PARTS8.3 Right Side CoverDetaching the right side cover(1) Detach the top cover (see Section 8.1).(2) Remove the two M4L8 TP screws on the right side of the scanner unit.Right side coverM4L8 TP screwNote:There is a positioning pillar inside the right side cover.Do not twist the cover when removing the cover.Otherwise, you will break the positioning pillar.(2) Disconnect the control panel cable from the control panel board.Positioning pillarRight side coverControl panel cableControl panel board(3) Detach the right side cover.Reattaching the right side cover(1) Reattach the right side cover in the reverse order in which it was detached.SK200-UM-251-9370 8-3
Page 2 and 3: HISTORY OF REVISIONSNo. Date issued
Page 7: 1. OVERVIEW1. OVERVIEW1.1 Standard
Page 12: 2. PART NAMES AND FUNCTIONS(10) EJE
Page 15 and 16: 3. CONNECTION AND PREPARATIONS3.1 C
Page 17 and 18: 3. CONNECTION AND PREPARATIONSR3.3
Page 21: 4. INSTALLING THE SOFTWARE4.2 Insta
Page 24 and 25: 4. INSTALLING THE SOFTWARE4.4 Check
Page 26: 5. DAILY MAINTENANCE5.2 Cleaning th
Page 29 and 30: 5. DAILY MAINTENANCE5.5 Cleaning th
Page 31 and 32: 5. DAILY MAINTENANCE5.7 Scanner Cal
Page 33 and 34: 5. DAILY MAINTENANCECalibrationBefo
Page 35 and 36: 5. DAILY MAINTENANCEColor Correctio
Page 37: 5. DAILY MAINTENANCE(10) The follow
Page 41: 7. LIST OF JIGS AND TOOLS7. LIST OF
Page 46 and 47: 8. DISASSEMBLING AND ADJUSTING THE
Page 56 and 57: 8.13 CIS Sensor Unit AssembliesDeta
Page 78 and 79: 9. ADJUSTMENTS USING THE SOFTWARE(5
Page 80 and 81: 9. ADJUSTMENTS USING THE SOFTWARE9.
Page 92 and 93: 9. ADJUSTMENTS USING THE SOFTWARETi
Page 94 and 95:
9. ADJUSTMENTS USING THE SOFTWARE4.
Page 96 and 97:
9. ADJUSTMENTS USING THE SOFTWARE9.
Page 98 and 99:
10. TROUBLESHOOTINGCause Checkpoint
Page 101 and 102:
12. PARTS LISTS12. PARTS LISTS12.1
Page 103 and 104:
12. PARTS LISTS12.3 Side CoverNo. P
Page 105:
12. PARTS LISTS12.5 Feed SectionNo.
Page 108 and 109:
12. PARTS LISTS12.8 Upper Section 2
Page 110 and 111:
12. PARTS LISTS12.10 Rear CIS Senso
Page 113 and 114:
12341234123412341234321125613513232
Page 115 and 116:
SK200-UM-251-9370 13-313. BLOCK DIA
Page 117 and 118:
SK200-UM-251-9370 13-513. BLOCK DIA
Page 119:
SK200-UM-251-9370 13-713. BLOCK DIA
Page 122 and 123:
SK200-UM-251-9370 13-1013. BLOCK DI
Page 124 and 125:
SK200-UM-251-9370 13-1213. BLOCK DI
Page 126 and 127:
SK200-UM-251-9370 13-1413. BLOCK DI
Page 128 and 129:
SK200-UM-251-9370 13-1613. BLOCK DI
Page 130 and 131:
13.2.2 CIS Controller Board for SK2
Page 132 and 133:
SK200-UM-251-9370 13-2013. BLOCK DI
Page 134 and 135:
13. BLOCK DIAGRAM AND CIRCUIT DIAGR
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
13.2.6 Data Controller Board for SK
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
SK200-UM-251-9370 13-4413. BLOCK DI
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164:
show all

SK200-UM-251 - Graphtec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?