SK200-UM-251 - Graphtec

More documents

Recommendations

Info

9. ADJUSTMENTS USING THE SOFTWARE(12) Click anywhere within the Origin box. The crosshairs cursor appears in the Scanner Adjustment window.0(13) When the crosshairs cursor appears in the Scanner Adjustment window, click on the center of the topcenter circle with the crosshairs cursor.(14) Click the "Check" button, then click the "Set" button. The following dialog box will appear.Click the "OK" button.(15) Scan the offset target chart again.Confirm that the starting point of the scanning is within the top center circle as shown below.SK200-UM-251-9370 9-14
9. ADJUSTMENTS USING THE SOFTWARESensor joint alignment (X Overlap, Y Offset)(1) When continuing with sensor joint alignment after offset adjustment, scroll the adjusted image to displaythe portion shown below.If you start with sensor joint alignment, follow Steps (1) through (4) in "Adjusting offset (origin)" on p.9-11 and 9-12 to display the scanned image, and scroll to display the portion shown below.Click here first.Click here next.(2) The image appears as shown above, with the left-hand portion of the image misaligned with the righthandportion. Click anywhere in the X Overlap box under "2-3." The crosshairs cursor will appear. Firstclick a position on the left-hand portion, then click the position of the right-hand portion that correspondsto the position you selected first.(3) Click the "Check" button first, then click the "Set" button. Follow the on-screen instruction to place theadjustment chart on the scanner again.(4) Repeat these steps until the left-hand portion is properly aligned with the right-hand portion.In this task, you need to adjust the X overlap and Y offset at the same time.See "Tips for Making Fine Adjustments" on the next page if you encounter difficulties making fineadjustments.(5) Similarly, make adjustments for 3-4, 1-2, and 4-5 in this order.After finishing, close all the adjustment menu windows. Use the SK200 test chart to perform a normalscan, and confirm that the image appears properly.Image after adjustmentsSK200-UM-251-9370 9-15
Page 2 and 3:
HISTORY OF REVISIONSNo. Date issued
Page 7:
1. OVERVIEW1. OVERVIEW1.1 Standard
Page 12:
2. PART NAMES AND FUNCTIONS(10) EJE
Page 15 and 16:
3. CONNECTION AND PREPARATIONS3.1 C
Page 17 and 18:
3. CONNECTION AND PREPARATIONSR3.3
Page 21:
4. INSTALLING THE SOFTWARE4.2 Insta
Page 24 and 25:
4. INSTALLING THE SOFTWARE4.4 Check
Page 26:
5. DAILY MAINTENANCE5.2 Cleaning th
Page 29 and 30:
5. DAILY MAINTENANCE5.5 Cleaning th
Page 31 and 32:
5. DAILY MAINTENANCE5.7 Scanner Cal
Page 33 and 34:
5. DAILY MAINTENANCECalibrationBefo
Page 35 and 36:
5. DAILY MAINTENANCEColor Correctio
Page 37:
5. DAILY MAINTENANCE(10) The follow
Page 41: 7. LIST OF JIGS AND TOOLS7. LIST OF
Page 44 and 45: 8. DISASSEMBLING AND ADJUSTING THE
Page 56 and 57: 8.13 CIS Sensor Unit AssembliesDeta
Page 78 and 79: 9. ADJUSTMENTS USING THE SOFTWARE(5
Page 80 and 81: 9. ADJUSTMENTS USING THE SOFTWARE9.
Page 92 and 93: 9. ADJUSTMENTS USING THE SOFTWARETi
Page 98 and 99: 10. TROUBLESHOOTINGCause Checkpoint
Page 101 and 102: 12. PARTS LISTS12. PARTS LISTS12.1
Page 103 and 104: 12. PARTS LISTS12.3 Side CoverNo. P
Page 105: 12. PARTS LISTS12.5 Feed SectionNo.
Page 108 and 109: 12. PARTS LISTS12.8 Upper Section 2
Page 110 and 111: 12. PARTS LISTS12.10 Rear CIS Senso
Page 113 and 114: 12341234123412341234321125613513232
Page 115 and 116: SK200-UM-251-9370 13-313. BLOCK DIA
Page 117 and 118: SK200-UM-251-9370 13-513. BLOCK DIA
Page 119: SK200-UM-251-9370 13-713. BLOCK DIA
Page 122 and 123: SK200-UM-251-9370 13-1013. BLOCK DI
Page 130 and 131: 13.2.2 CIS Controller Board for SK2
Page 134 and 135: 13. BLOCK DIAGRAM AND CIRCUIT DIAGR
Page 140 and 141:
13.2.6 Data Controller Board for SK
Page 142 and 143:
13. BLOCK DIAGRAM AND CIRCUIT DIAGR
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
SK200-UM-251-9370 13-4413. BLOCK DI
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164:
show all

SK200-UM-251 - Graphtec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?