SK200-UM-251 - Graphtec

More documents

Recommendations

Info

8. DISASSEMBLING AND ADJUSTING THE MECHANICAL PARTS8.8 Feed Drive Belt (60S2M250)Detaching the feed drive belt(1) Detach the top and left side covers (see Sections 8.1 and 8.2).(2) Loosen the two M4L6 binding head screws holding the feed belt tension bracket.(3) Detach the feed drive belt from the feed pulley.Feed drive beltM4L6 binding head screwReattaching the feed drive belt(1) Reattach the feed drive belt by reversing the sequence of steps in which it was detached.(2) Adjust the belt tension (see Section 8.9).SK200-UM-251-9370 8-8
8. DISASSEMBLING AND ADJUSTING THE MECHANICAL PARTS8.9 Adjusting Feed Drive Belt Tension (60S2M250)Adjusting the feed drive belt tension(1) Loosen the two M4L6 binding head screws holding the feed drive belt tension bracket.(2) Loop the wire around the feed pulleys as shown in the photograph below.2 kgfPush/pull gaugeWireM4L6 binding head screwFeed pulleyFeed drive belt tension pulley(3) Use the push/pull gauge to pull the feed drive belt tension pulleys with a 2 kg force as shown above.(4) Tighten the two M4L6 binding head screws that hold the feed drive belt tension bracket.SK200-UM-251-9370 8-9
Page 2 and 3: HISTORY OF REVISIONSNo. Date issued
Page 7: 1. OVERVIEW1. OVERVIEW1.1 Standard
Page 12: 2. PART NAMES AND FUNCTIONS(10) EJE
Page 15 and 16: 3. CONNECTION AND PREPARATIONS3.1 C
Page 17 and 18: 3. CONNECTION AND PREPARATIONSR3.3
Page 21: 4. INSTALLING THE SOFTWARE4.2 Insta
Page 24 and 25: 4. INSTALLING THE SOFTWARE4.4 Check
Page 26: 5. DAILY MAINTENANCE5.2 Cleaning th
Page 29 and 30: 5. DAILY MAINTENANCE5.5 Cleaning th
Page 31 and 32: 5. DAILY MAINTENANCE5.7 Scanner Cal
Page 33 and 34: 5. DAILY MAINTENANCECalibrationBefo
Page 35 and 36: 5. DAILY MAINTENANCEColor Correctio
Page 37: 5. DAILY MAINTENANCE(10) The follow
Page 41: 7. LIST OF JIGS AND TOOLS7. LIST OF
Page 44 and 45: 8. DISASSEMBLING AND ADJUSTING THE
Page 56 and 57: 8.13 CIS Sensor Unit AssembliesDeta
Page 78 and 79: 9. ADJUSTMENTS USING THE SOFTWARE(5
Page 80 and 81: 9. ADJUSTMENTS USING THE SOFTWARE9.
Page 92 and 93: 9. ADJUSTMENTS USING THE SOFTWARETi
Page 98 and 99: 10. TROUBLESHOOTINGCause Checkpoint
Page 101 and 102:
12. PARTS LISTS12. PARTS LISTS12.1
Page 103 and 104:
12. PARTS LISTS12.3 Side CoverNo. P
Page 105:
12. PARTS LISTS12.5 Feed SectionNo.
Page 108 and 109:
12. PARTS LISTS12.8 Upper Section 2
Page 110 and 111:
12. PARTS LISTS12.10 Rear CIS Senso
Page 113 and 114:
12341234123412341234321125613513232
Page 115 and 116:
SK200-UM-251-9370 13-313. BLOCK DIA
Page 117 and 118:
SK200-UM-251-9370 13-513. BLOCK DIA
Page 119:
SK200-UM-251-9370 13-713. BLOCK DIA
Page 122 and 123:
SK200-UM-251-9370 13-1013. BLOCK DI
Page 124 and 125:
SK200-UM-251-9370 13-1213. BLOCK DI
Page 126 and 127:
SK200-UM-251-9370 13-1413. BLOCK DI
Page 128 and 129:
SK200-UM-251-9370 13-1613. BLOCK DI
Page 130 and 131:
13.2.2 CIS Controller Board for SK2
Page 132 and 133:
SK200-UM-251-9370 13-2013. BLOCK DI
Page 134 and 135:
13. BLOCK DIAGRAM AND CIRCUIT DIAGR
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
13.2.6 Data Controller Board for SK
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
SK200-UM-251-9370 13-4413. BLOCK DI
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164:
show all

SK200-UM-251 - Graphtec

Create successful ePaper yourself

Delete template?

Save as template?