SK200-UM-251 - Graphtec

More documents

Recommendations

Info

9. ADJUSTMENTS USING THE SOFTWARE9.2 Preparations before Making AdjustmentsNote the current feed distance adjustment and position adjustment values while making adjustments.This enables the values to be entered directly from the keyboard to restore the scanner to its previous statusif adjustment fails.In main board replacement, the time required for adjustment can be reduced by setting the previously notedfeed distance adjustment and position adjustment values. However, for image sensor unit replacement, allsettings must be adjusted, eliminating the need to record the previous values.Adjustment Procedure(1) Start Scanning Master 21+. (See p. 9-1.)(2) Select "Adjust Feed Distance" from the "Adjust" menu.(3) Click the "Current Value" button and note the value shown in the Feed Adjustment Value box. Afterfinishing, click the "Close" button.(4) Similarly, select "Adjust Position" from the "Adjust" menu and click the "Current Value" button. Note thevalues shown in the X Overlap and Y Offset boxes and click the "Close" button.SK200-UM-251-9370 9-4
9. ADJUSTMENTS USING THE SOFTWARE9.3 Preparing a Test Chart(1) Prepare a SK200 adjustment test chart.(2) Make sure that the distances (measured with a glass scale) between the two points in all pairs areincluded in the chart in advance. (See the chart shown above.) The test chart is made of Mylar paper.For use in normal office environments (normal temperatures and humidity levels), you shouldonly need to measure each distance once.Make sure that each distance is measured with the utmost accuracy. Make sure that all staff members using this test chart select the same measurement points.This chart has been designed with the assumption that the point shown below is used formeasurement.If user-specified paper must be used for adjustments, you should make the measurements overas long a period of time as possible to obtain good results.SK200-UM-251-9370 9-5
Page 2 and 3:
HISTORY OF REVISIONSNo. Date issued
Page 7:
1. OVERVIEW1. OVERVIEW1.1 Standard
Page 12:
2. PART NAMES AND FUNCTIONS(10) EJE
Page 15 and 16:
3. CONNECTION AND PREPARATIONS3.1 C
Page 17 and 18:
3. CONNECTION AND PREPARATIONSR3.3
Page 21:
4. INSTALLING THE SOFTWARE4.2 Insta
Page 24 and 25:
4. INSTALLING THE SOFTWARE4.4 Check
Page 26:
5. DAILY MAINTENANCE5.2 Cleaning th
Page 29 and 30: 5. DAILY MAINTENANCE5.5 Cleaning th
Page 31 and 32: 5. DAILY MAINTENANCE5.7 Scanner Cal
Page 33 and 34: 5. DAILY MAINTENANCECalibrationBefo
Page 35 and 36: 5. DAILY MAINTENANCEColor Correctio
Page 37: 5. DAILY MAINTENANCE(10) The follow
Page 41: 7. LIST OF JIGS AND TOOLS7. LIST OF
Page 44 and 45: 8. DISASSEMBLING AND ADJUSTING THE
Page 56 and 57: 8.13 CIS Sensor Unit AssembliesDeta
Page 78 and 79: 9. ADJUSTMENTS USING THE SOFTWARE(5
Page 82 and 83: 9. ADJUSTMENTS USING THE SOFTWARE9.
Page 92 and 93: 9. ADJUSTMENTS USING THE SOFTWARETi
Page 98 and 99: 10. TROUBLESHOOTINGCause Checkpoint
Page 101 and 102: 12. PARTS LISTS12. PARTS LISTS12.1
Page 103 and 104: 12. PARTS LISTS12.3 Side CoverNo. P
Page 105: 12. PARTS LISTS12.5 Feed SectionNo.
Page 108 and 109: 12. PARTS LISTS12.8 Upper Section 2
Page 110 and 111: 12. PARTS LISTS12.10 Rear CIS Senso
Page 113 and 114: 12341234123412341234321125613513232
Page 115 and 116: SK200-UM-251-9370 13-313. BLOCK DIA
Page 117 and 118: SK200-UM-251-9370 13-513. BLOCK DIA
Page 119: SK200-UM-251-9370 13-713. BLOCK DIA
Page 122 and 123: SK200-UM-251-9370 13-1013. BLOCK DI
Page 130 and 131:
13.2.2 CIS Controller Board for SK2
Page 132 and 133:
SK200-UM-251-9370 13-2013. BLOCK DI
Page 134 and 135:
13. BLOCK DIAGRAM AND CIRCUIT DIAGR
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
13.2.6 Data Controller Board for SK
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
SK200-UM-251-9370 13-4413. BLOCK DI
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164:
show all

SK200-UM-251 - Graphtec

Create successful ePaper yourself

Delete template?

Save as template?