i agree and wish to proceed with download - Roland Systems Group ...

More documents

Recommendations

Info

Monitor/SoloUsing Solo1. In the top panel MONITOR section, press [DISP].fig.ScrMonitor.epsThe MONITOR screen will appear.2. Use the SOLO MODE select buttons to select the desiredsolo mode.3. Use [F1 (CH SOLO AFL)] to select the point from which theinput channel signal will be sent to solo.4. On the top panel, press [SOLO] for the desired channel.The signal of that channel will be sent to Solo, and output fromthe output jacks to which MONITOR OUT L/R are patched,and from the PHONES jack.5. Use the SOLO Lev knob to adjust the solo level.6. Use the MONITOR section’s LEVEL knob or the PHONESLEVEL knob to adjust the monitor output level.Monitor/SoloIf the solo mode is ADD ON, soloing will be controlled so thatinput channels, output channels (AUX channels, MATRIXchannels and MAIN L/R channels), and DCA groups are notsoloed at the same time. If the Solo mode is ADD ON, theselection will be controlled so that the solo signal does notinclude both input channels and output channels (AUXchannels and MAIN L/R channel). For example, if an inputchannel is soloed, and you turn on Solo for an AUX channel, thesolo setting of the input channel will be defeated and Solo willbe turned on for the AUX channel.124
Scene memoryAbout scene memoryScene memory is a function that lets you store mixer parameters as ascene, and recall them when desired. Scene memory is a functionthat lets you store and recall mixing parameters as “scenes.” The M-380 can store 300 scenes in its internal memory, and you can assign asixteen-character name to each scene.The following scene functions are also provided.• LockProhibits overwriting, deletion, renaming, or editing for thescene. (p. 127)• Recall Filter functionSpecifies the parameters that will be recalled for each scene.(p. 127)• Global Scope functionSpecifies the region (channels, parameters) that will be recalledfor all scenes. (p. 131)The following mixer parameters are stored in a scene.• Preamp (input/output unit, and the M-380’s CONSOLE INPUT)• Input patchbay• Output patchbay• CH1–CH48• AUX1–AUX16, MATRIX1–MATRIX8, MAIN L/R, MAIN C• Effects• Talkback/Oscillator• DCA groups, MUTE groups• USB memory recorderThe following parameter are not stored in a scene.•The status of the TALKBACK button.•The position of the TALKBACK MIC LEVEL knob.•The status of the TALKBACK phantom power.•The setting of the monitor.•The statuses of the SOLO buttons.•The recorder status (eg, playing or recording) of the USBmemory recorder.•The playback mode of the USB memory recorder.•The song selection of the USB memory recorder.1. Scene numberThis indicates the number of the currently selected scene. If thenumber is blinking, a number other than the current scenenumber is selected.The current mixer parameters are referred to as the currentscene. The scene number that was most recently recalled orstored is called the “current scene number.”2. Scene nameThis indicates the name of the currently selected scene. Thescene name is not shown for a blank scene (a scene in whichnothing has been stored).3. E symbolThis will be shown if the mixer parameters have been editedafter the scene was recalled or stored.Since this means that the mixer parameters no longer match thedata in scene memory, you’ll need to store them into a scenememory if you want to keep them.4. LOCK symbolThis indicates whether the currently selected scene is locked.You cannot store to a locked scene or delete it.Operations in the SCENEscreenThe SCENE screen is used to edit the scene list and make variousscene settings.Accessing the SCENE screen1. In the SCENE MEMORY section, press [DISP].The SCENE screen will appear.fig.ScrSceneListGuide.epsAScene memoryAbout the scene indication in thetop display areafig.ScrTBSceneDispGuide.eps1 3 42Basic information about the scene is shown in the top display area.A.Scene listThis lists the scenes. The current scene is shown in green.The list shows the following items.125
Page 1 and 2:
Owner’s ManualBefore using this u
Page 3 and 4:
USING THE UNIT SAFELYUsed for instr
Page 5 and 6:
120• Always turn the phantom powe
Page 7 and 8:
IMPORTANT NOTESMemory Backup501b•
Page 9:
IMPORTANT NOTES9
Page 12 and 13:
ContentsContentsScene memory ......
Page 14 and 15:
IntroductionCheck the included item
Page 16 and 17:
IntroductionPlacementAbout the REAC
Page 18 and 19:
IntroductionTurning the power on/of
Page 20 and 21:
IntroductionAbout USB memoryIntrodu
Page 22:
Explanation of the panelsTop panelf
Page 25 and 26:
Explanation of the panelsC. PREAMP
Page 27 and 28:
Explanation of the panels• SENDS
Page 29 and 30:
Explanation of the panels14. MONITO
Page 31 and 32:
Explanation of the panels1. CONSOLE
Page 33 and 34:
Explanation of the panels12. Ground
Page 35 and 36:
Basic operationAccessing a screenWh
Page 37 and 38:
Basic operation3. Sub-display areaT
Page 39 and 40:
Basic operationEditing a nameLibrar
Page 41 and 42:
Basic operationEditing the name of
Page 43 and 44:
Input channel operationsOperations
Page 45 and 46:
Input channel operationsSending the
Page 47 and 48:
Input channel operations3. Filter5.
Page 49 and 50:
Input channel operations• AUX pan
Page 51 and 52:
Input channel operationsSpecifying
Page 53 and 54:
Input channel operations5. Press [F
Page 55 and 56:
AUX channel and MAIN L/R channel op
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
MATRIX channel operationsMATRIX cha
Page 69 and 70:
MATRIX channel operations2. Insert
Page 71 and 72:
MATRIX channel operationsThe functi
Page 73 and 74: DynamicsGate/expander operationsA g
Page 75 and 76: DynamicsGatefig.PopGateGuide2.epsb.
Page 77 and 78: DynamicsA.OverviewThis shows the ov
Page 79 and 80: Dynamics2. IN meterThis indicates t
Page 81 and 82: Dynamicsfig.ScrCompOverviewGuide2.e
Page 83 and 84: DynamicsAccessing the LIMITER popup
Page 85 and 86: Four-band EQE.FT ATT knobThis adjus
Page 87 and 88: AUX send/MATRIX sendAUX send operat
Page 89 and 90: AUX send/MATRIX sendMATRIX send ope
Page 91 and 92: Input/output patchbayb.Jack indicat
Page 93 and 94: Input/output patchbayIf you attempt
Page 95 and 96: MeteringViewing the channel strip o
Page 97 and 98: MeteringB.SRC (source)This selects
Page 99 and 100: Effects and 31-band GEQFX 1-4 tab
Page 101 and 102: Effects and 31-band GEQB.Output cha
Page 103 and 104: Effects and 31-band GEQfig.ScrFxLib
Page 105 and 106: Effects and 31-band GEQInserting a
Page 107 and 108: Effects and 31-band GEQ8-band param
Page 109 and 110: Effects and 31-band GEQUsing the an
Page 111 and 112: Inserting an external effects devic
Page 113 and 114: Inserting an external effects devic
Page 115 and 116: DCA groupsAssigning a channel to aD
Page 117 and 118: Mute groupsAbout mute groupsMute gr
Page 119 and 120: Talkback/OscillatorAbout talkback a
Page 121 and 122: Talkback/OscillatorUsing the oscill
Page 123: Monitor/SoloAccessing the MONITOR s
Page 127 and 128: Scene memoryRecalling a scene memor
Page 129 and 130: Scene memoryEditing the scene listT
Page 131 and 132: Scene memoryThe Global Scope functi
Page 133 and 134: Scene memory6. Press [F8 (STORE)].f
Page 135 and 136: LCR SYSTEMLCR SYSTEM settingsThe LC
Page 137 and 138: LCR SYSTEM4. Use the AUX select but
Page 139 and 140: LCR SYSTEM2. Centr (center)This spe
Page 141 and 142: USB memory recorderAbout the USB me
Page 143 and 144: USB memory recorderSpecifying the i
Page 145 and 146: USB memory recorderRenaming a WAV f
Page 147 and 148: User settingsAccessing the USER scr
Page 149 and 150: User settingsSaving the current use
Page 151 and 152: User settingsLimiting the range ofp
Page 153 and 154: User settings[F1 (LAYER 1/2)] Acces
Page 155 and 156: User settingsEditing other user pre
Page 157 and 158: REAC applications and settingsREAC
Page 159 and 160: REAC applications and settingsREAC
Page 161 and 162: REAC applications and settingsBacku
Page 163 and 164: REAC applications and settings5. Us
Page 165 and 166: RemoteThis chapter explains remote
Page 167 and 168: RemoteV-LINK settingsTo make V-LINK
Page 169 and 170: RemoteRS-232C settingsThe RS-232C t
Page 171 and 172: Other settings and functions3. Use
Page 173 and 174: Other settings and functionsSaving
Page 175 and 176:
Other settings and functions5. Use
Page 177 and 178:
Other settings and functionsFormatt
Page 179 and 180:
Other settings and functionsConsole
Page 181 and 182:
Other settings and functionsSystem
Page 183 and 184:
Other settings and functionsIf the
Page 185 and 186:
Management of the M-48 live persona
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
AppendixError message listMessagexx
Page 211 and 212:
Appendix(p. 171) so that touch sens
Page 213 and 214:
AppendixMain specificationsM-380: M
Page 215 and 216:
AppendixDisplay800 x 480 dots Wide
Page 217 and 218:
Effect typesReverbSt.REVERB (Stereo
Page 219 and 220:
AppendixTypes of soundREVERB+GATEfi
Page 221 and 222:
AppendixLSV (Low Shelving)Boosts/cu
Page 223 and 224:
AppendixLONG DELAYΩig.AlgoLongDela
Page 225 and 226:
AppendixWET POSITIONThe wet positio
Page 227 and 228:
AppendixPitch shiftP.SHIFTER x2 (Pi
Page 229 and 230:
AppendixLO-MID QSteepness of the fr
Page 231 and 232:
AppendixLFD FREQ (LF damp frequency
Page 233 and 234:
AppendixDIRECT Sw (Direct Switch)Sp
Page 235 and 236:
AppendixSBF-325(STEREO FLANGER SBF-
Page 237 and 238:
IndexSymbols+48V ..................
Page 239 and 240:
IndexREAC A port ..................
Page 241 and 242:
Screen indexREAC CONFIG popup (SETU
Page 243 and 244:
Block Diagram (LCR SYSTEM: ON)TO RE
Page 245 and 246:
For EU CountriesApparatus containin
show all

i agree and wish to proceed with download - Roland Systems Group ...

Create successful ePaper yourself

Delete template?

Save as template?