HMI software for CNC controls

More documents

Recommendations

Info

4 HMI software for CNC controls Motion Control Information System MCIS MDA – Machine Data Acquisition MDA Machine ■ Overview MDA Machine software is used by SINUMERIK controls to acquire and analyze information (such as status, quantities, alarms and messages) at the machine. ■ Benefits 7 Up-to-date machine data allow swift responses 7 Greater transparency at the machine and in the production process leads to earlier recognition of possible improvements 7 Targeted actions increase machine utilization times 7 Verification of machine performance through objectively established indicators and performance data (OEE number, availability, capacity utilization, performance, quality) ■ Function • Automatic acquisition of machine data from the open interface in the DB13/14 standard data blocks of the PLC. Alternatively, 5 fixed states can be acquired via the plug-and-play interface. - Machine status, processing results via DB - Total piece counts DB - Types of pieces, piece type-specific piece counts via DB - Cycle times via DB - Alarms and messages (only with SINUMERIK) • Manual status entry, fault explanation by the operator • Automatic buffer storage of the acquired data on the hard drive of SINUMERIK. In the event of a network failure, these data are then automatically tracked by MDA Cell/MDA Plant. • Export function to Excel, print-out of tables, hardcopy • Analyses: - Workpiece counter (machine-specific and part-specific) - Current states - Fault analysis - Status analysis - Shift/daily/weekly/monthly total - Logbook, (Prio) protocol - Availability/capacity utilization - History of availability/capacity utilization - Key performance indicators (capacity utilization, availability) - Alarm statistics, alarm log, current alarms (for SINUMERIK only) One MDA Machine license is required for each connected SINUMERIK or OPC control. 4/44 Siemens NC 60 · 2006 ■ Integration Preconditions: • SINUMERIK 810D powerline/840Di/840D powerline with PCU 50/PCU 70 If several equipment units are to be operated and analyzed on one machine, additional MDA IFC licenses must be obtained. For each operator panel, up to 8 equipment units can be evaluated: 1 MDA Machine license and up to 7 additional MDA IFC licenses. �� MDA IFC MDA Machine + MDA IFC The system can be expanded with MDA Cell. For each operator panel, up to 8 equipment units (MDA IFC licenses) can be acquired. For each MDA Cell, a total of 16 machines/equipment units can be evaluated. �� MDA Cell ��
■ Selection and Ordering Data Designation Order No. MDA Machine Software for machine data acquisition and evaluation on CD-ROM Languages: English, French, German, Italian, Spanish • Single license for current software version • Single license for specific software version • Single license without data carrier • Upgrade on order of specific software version • Trial license Single license for current software version • Trial license Single license for specific software version 6FC6000-3AC00-0AA0 6FC6000-3AC07-7AA0 6FC6000-3AF00-0AB0 6FC6000-3AC07-7AE0 6FC6000-3AC00-0AT7 6FC6000-3AC07-7AT7 Example of "specific software version", e.g. 2.0: 6FC6000-3AC02-0A.. HMI software for CNC controls Motion Control Information System MCIS MDA – Machine Data Acquisition MDA Machine ■ More information Additional information is available in the Internet under: http://www.siemens.com/automation/support Siemens NC 60 · 2006 4/45 4
Page 1 and 2: HMI software for CNC controls 4/2 O
Page 3 and 4: ■ Overview The HMI-Advanced softw
Page 5 and 6: ■ Overview The ManualTurn operato
Page 7 and 8: ■ Selection and Ordering Data Des
Page 11 and 12: ■ Overview Measuring cycles Examp
Page 13 and 14: ■ Overview HMI software for CNC c
Page 15 and 16: HMI software for CNC controls Open
Page 17 and 18: ■ Overview EasyMask is a simple c
Page 19 and 20: ■ Overview Introduction With the
Page 21 and 22: ■ Overview DNC Cell supports hand
Page 23 and 24: ■ Overview DNC - Direct Numeric C
Page 25 and 26: ■ Overview DNC Compare is a suppl
Page 27 and 28: HMI software for CNC controls Motio
Page 31 and 32: ■ Overview Using the convenient d
Page 33 and 34: ■ Overview TDI Statistic provides
Page 37 and 38: ■ Overview With TDI Machine, tool
Page 41 and 42: ■ Overview MDA Cell is used to co
Page 43: ■ Overview The MDA IFC Interface
Page 47 and 48: ■ Overview MCIS TPM provides supp
Page 49 and 50: ■ Overview HMI software for CNC c
Page 51 and 52: ■ Overview Remote diagnostics int
Page 55 and 56: HMI software for CNC controls ePS N
Page 57 and 58: ■ Overview The MOBY I contactless
Page 59 and 60: ■ Overview The write/read device
Page 61 and 62: ■ Technical specifications Type C
Page 63 and 64: HMI software for CNC controls Tools
Page 65 and 66: HMI software for CNC controls SINUM
Page 67 and 68: ■ Overview Comara KG Intelligent
Page 69 and 70: ■ Overview TwinCAM 32 CNC program
Page 71 and 72: MARPOSS S.p.A. Measuring, balancing
Page 73 and 74: ■ Overview MPM - Micro Präzision
Page 75 and 76: ■ Overview PROMETEC GmbH PROSIN d

HMI software for CNC controls

Create successful ePaper yourself

Delete template?

Save as template?