11-12 GA-1120 Color Management - Toshiba

More documents

Recommendations

Info

2-20 Color Calibration When the patch has been measured successfully, a checkmark appears in the patch preview in the Measurements window. The window identifies and highlights the next patch to be measured. 10. Repeat step 9 to measure each successive patch on the Measurement Page. To retake a measurement, first select the desired patch preview in the Measurements window. Then measure the patch on the page using the ED-100. NOTE: You must take the measurements in the order outlined in the Measurements window and on the measurement page. 11. When all the patches have been read successfully, click Accept. 12. Click Apply in the Calibrator window to implement the new calibration set. 13. Click OK in the Information dialog box. This completes the GA-1120 calibration process.
2-21 Using AutoCal and ColorCal Using AutoCal and ColorCal AutoCal and ColorCal let you calibrate the GA-1120 without the use of an additional spectrophotometer or densitometer. Instead, these methods use the copier’s built-in scanner to measure toner density values. You can perform AutoCal and ColorCal calibration from either ColorWise Pro Tools or the GA-1120 Control Panel. For troubleshooting during the AutoCal procedure, see the Job Management Guide. NOTE: To calibrate using AutoCal or ColorCal, you will need the Kodak Gray Scale strip included in the customer media pack that came with your GA-1120. Calibrating with ColorWise Pro Tools and AutoCal or ColorCal When you run ColorCal from ColorWise Pro Tools, you have the option to calibrate the copier’s scanner before calibrating the GA-1120 itself. This option is not available for AutoCal. TO CALIBRATE WITH COLORWISE PRO TOOLS AND AUTOCAL OR COLORCAL 1. Start Calibrator. For instructions on starting Calibrator, see page 2-6. 2. In the Select Measurement Method pane, choose AutoCal or ColorCal. 3. In the Check Print Settings pane, choose the desired calibration set. If more than one option appears, choose the appropriate calibration set for the type of media you will use most often. NOTE: For this calibration to take effect, the calibration set must be associated with one or more output profiles. The default calibration set is already associated with the default output profile, so there is no need to make any new associations. 4. Click Print in the Generate Measurement Page pane.
Page 1 and 2:
TOSHIBA GA-1120 COLOR GUIDE
Page 3 and 4: Copyright © 2002 Electronics For I
Page 5: Proprietary Rights You acknowledge
Page 8 and 9: viii Contents Starting Calibrator 2
Page 11 and 12: Introduction xi About this manual T
Page 13: xiii Key features of ColorWise Colo
Page 16 and 17: RGB data CMYK data Spot color data
Page 18 and 19: RGB Separation Output/Simulation 1-
Page 20 and 21: 1-6 GA-1120 Color Management select
Page 22 and 23: 1-8 GA-1120 Color Management If you
Page 24 and 25: 1-10 GA-1120 Color Management The C
Page 26 and 27: 1-12 GA-1120 Color Management are p
Page 28 and 29: 1-14 GA-1120 Color Management • O
Page 30 and 31: Choose ColorWise 1-16 GA-1120 Color
Page 32 and 33: 1-18 GA-1120 Color Management Setti
Page 34 and 35: 1-20 GA-1120 Color Management 3. In
Page 36 and 37: 2-2 Color Calibration An overview o
Page 38 and 39: 2-4 Color Calibration Output profil
Page 40 and 41: 2-6 Color Calibration Starting Cali
Page 42 and 43: Calibration methods appear here 2-8
Page 44 and 45: 2-10 Color Calibration Restoring de
Page 46 and 47: 2-12 Color Calibration 8. Click Mea
Page 48 and 49: 2-14 Color Calibration Calibrating
Page 50 and 51: Indicator light Sample aperture (un
Page 52 and 53: 2-18 Color Calibration In the Paper
Page 56 and 57: 2-22 Color Calibration 5. Choose th
Page 58 and 59: 2-24 Color Calibration Calibrating
Page 60 and 61: 2-26 Color Calibration TO REMOVE CA
Page 62 and 63: 3-2 ColorWise Pro Tools NOTE: If yo
Page 64 and 65: 3-4 ColorWise Pro Tools 4. Click OK
Page 66 and 67: 3-6 ColorWise Pro Tools TO BACK UP
Page 68 and 69: 3-8 ColorWise Pro Tools TO DEFINE A
Page 70 and 71: 3-10 ColorWise Pro Tools Simulation
Page 72 and 73: 3-12 ColorWise Pro Tools 4. For a s
Page 74 and 75: A curve with this shape makes a col
Page 76 and 77: 3-16 ColorWise Pro Tools TO EDIT A
Page 78 and 79: 3-18 ColorWise Pro Tools TO CORRECT
Page 80 and 81: 3-20 ColorWise Pro Tools 8. In the
Page 82 and 83: 3-22 ColorWise Pro Tools Color Setu
Page 85 and 86: Appendix A: Color Measurement Instr
Page 87 and 88: Unused connector A-3 Color Measurem
Page 89 and 90: A-5 Color Measurement Instruments 6
Page 91 and 92: A-7 Color Measurement Instruments 7
Page 93 and 94: Unused connector Connect to compute
Page 95: A-11 Color Measurement Instruments
Page 98 and 99: B-2 Importing density measurements
Page 101 and 102: Index A Absolute Colorimetric rende
Page 103 and 104: I-3 Index calibration sets for 2-3,
show all

11-12 GA-1120 Color Management - Toshiba

Create successful ePaper yourself

Delete template?

Save as template?