11-12 GA-1120 Color Management - Toshiba

More documents

Recommendations

Info

A-8 Color Measurement Instruments 10. Insert the end of the Color Reflection Reference strip with the arrow into the calibration strip entrance on the DTP41, centering it below the alignment mark (see the diagram on page A-2). Insert the strip about 3 inches, past the front idler rollers, until it rests against the rear drive rollers. 11. Click Read Reference in the Instrument Calibration dialog box. The DTP41 pulls the calibration strip through automatically. A message appears in the Status area when the calibration is finished. 12. Click Done. 13. Close the Utilities window. This completes DTP41 calibration. When the DTP41 requires calibration, your computer prompts you. When the prompt message appears, click Calibrate Now and follow the instructions, starting with step 8 on page A-7. After calibrating the DTP41, calibrate the GA-1120 (see page 2-10). Using the X-Rite DTP32 densitometer ColorWise Pro Tools are designed to work with the X-Rite DTP32 reflection densitometer, which feeds color measurements to the GA-1120 automatically. NOTE: Measurements from other densitometers can be input using a simple ASCII file format (see Appendix B). Setting up the DTP32 Before you calibrate the GA-1120 using the X-Rite DTP32, you need to connect, configure, and calibrate the densitometer to prepare for measuring the printed patches (see “Calibrating the DTP32” on page A-11). For additional information about setting up and using the DTP32, see the separate documentation included with the densitometer.
Unused connector Connect to computer Connect to adapter A-9 Color Measurement Instruments TO CONNECT THE X-RITE DTP32 TO THE COMPUTER 1. Turn off the computer. 2. Plug the square end of the interface cable (looks like a modular phone plug) into the I/O port on the side of the X-Rite DTP32. 3. Attach the connector to the computer. Square connector For a Windows computer, insert the 8-pin mini-DIN end of the interface cable into the 9-pin DB9 Connector cable adapter. Insert the 9-pin end into the COM1 or COM2 port on the computer and tighten the screws. If the available port on your computer is 25-pin, you must use the 8-pin-to-25-pin adapter. Square connector Interface cable
Page 1 and 2:
TOSHIBA GA-1120 COLOR GUIDE
Page 3 and 4:
Copyright © 2002 Electronics For I
Page 5:
Proprietary Rights You acknowledge
Page 8 and 9:
viii Contents Starting Calibrator 2
Page 11 and 12:
Introduction xi About this manual T
Page 13:
xiii Key features of ColorWise Colo
Page 16 and 17:
RGB data CMYK data Spot color data
Page 18 and 19:
RGB Separation Output/Simulation 1-
Page 20 and 21:
1-6 GA-1120 Color Management select
Page 22 and 23:
1-8 GA-1120 Color Management If you
Page 24 and 25:
1-10 GA-1120 Color Management The C
Page 26 and 27:
1-12 GA-1120 Color Management are p
Page 28 and 29:
1-14 GA-1120 Color Management • O
Page 30 and 31:
Choose ColorWise 1-16 GA-1120 Color
Page 32 and 33:
1-18 GA-1120 Color Management Setti
Page 34 and 35:
1-20 GA-1120 Color Management 3. In
Page 36 and 37:
2-2 Color Calibration An overview o
Page 38 and 39:
2-4 Color Calibration Output profil
Page 40 and 41:
2-6 Color Calibration Starting Cali
Page 42 and 43: Calibration methods appear here 2-8
Page 44 and 45: 2-10 Color Calibration Restoring de
Page 46 and 47: 2-12 Color Calibration 8. Click Mea
Page 48 and 49: 2-14 Color Calibration Calibrating
Page 50 and 51: Indicator light Sample aperture (un
Page 52 and 53: 2-18 Color Calibration In the Paper
Page 54 and 55: 2-20 Color Calibration When the pat
Page 56 and 57: 2-22 Color Calibration 5. Choose th
Page 58 and 59: 2-24 Color Calibration Calibrating
Page 60 and 61: 2-26 Color Calibration TO REMOVE CA
Page 62 and 63: 3-2 ColorWise Pro Tools NOTE: If yo
Page 64 and 65: 3-4 ColorWise Pro Tools 4. Click OK
Page 66 and 67: 3-6 ColorWise Pro Tools TO BACK UP
Page 68 and 69: 3-8 ColorWise Pro Tools TO DEFINE A
Page 70 and 71: 3-10 ColorWise Pro Tools Simulation
Page 72 and 73: 3-12 ColorWise Pro Tools 4. For a s
Page 74 and 75: A curve with this shape makes a col
Page 76 and 77: 3-16 ColorWise Pro Tools TO EDIT A
Page 78 and 79: 3-18 ColorWise Pro Tools TO CORRECT
Page 80 and 81: 3-20 ColorWise Pro Tools 8. In the
Page 82 and 83: 3-22 ColorWise Pro Tools Color Setu
Page 85 and 86: Appendix A: Color Measurement Instr
Page 87 and 88: Unused connector A-3 Color Measurem
Page 89 and 90: A-5 Color Measurement Instruments 6
Page 91: A-7 Color Measurement Instruments 7
Page 95: A-11 Color Measurement Instruments
Page 98 and 99: B-2 Importing density measurements
Page 101 and 102: Index A Absolute Colorimetric rende
Page 103 and 104: I-3 Index calibration sets for 2-3,
show all

11-12 GA-1120 Color Management - Toshiba

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?