11-12 GA-1120 Color Management - Toshiba

More documents

Recommendations

Info

3-16 ColorWise Pro Tools TO EDIT A SIMULATION IN QUICK, FULL (SOURCE GCR), OR FULL (OUTPUT GCR) MODE 1. Start ColorWise Pro Tools and click Color Editor. 2. Choose Simulation from the View menu, select the simulation profile to edit, and then click Select. NOTE: You can also open the Profile Manager, select a simulation profile, and click Edit. 3. Choose Quick, Full (Source GCR), or Full (Output GCR) from the Edit Mode menu, and choose an output profile with which your edited simulation will be linked from the Link with menu. The edited simulation will be linked with the output profile you choose from the “Link with” menu. NOTE: When editing a simulation profile in Quick mode, clicking Import at the bottom of the Color Editor window lets you import a custom Quick Simulation created on another GA-1120 using the previous version of ColorWise. The current version of ColorWise does not allow you to save custom Quick or Full Simulations independently; rather, they are saved as components of the same profile.
3-17 Color Editor 4. Edit and save the simulation as described in steps 5 through 10 of the procedure starting on page 3-13. For this new simulation to be automatically applied to a print job, the CMYK Simulation, Simulation Method, and Output Profile settings must be the same as those used when you edited the profile. If the Simulation Method is different or a different output profile is selected, the Master simulation is applied. NOTE: A Simulation Profile can have a custom Master and one or more custom links— up to three links (Quick mode and the two Full modes) for each output profile on the system. (For the CMYK Simulation Profile option in the printer driver, note that if you select a custom profile for which the output ink percentage is greater than 0 and the input ink percentage is 0, the Use Master print option will have no effect.) Undoing simulation edits You can undo the changes you made to simulations (master and linked) in the following ways: • If you have not yet saved your edits, click Done on the Color Editor menu bar, and do not save the changes. • If you saved your edits under a new simulation name and want to delete all edits (in Master, Quick, and Full modes) to the simulation, see page 3-7. Adjusting gray balance The AutoGray feature lets you use the copier’s built-in scanner as a measurement device for adjusting the gray balance of output profiles. Gray balance refers to the quality of neutral gray tones in a profile. In many cases, gray tones may contain a bluish or reddish color cast. AutoGray helps shift these tones back toward neutral grays. If you are satisfied with the gray balance of the copier, you do not need to use AutoGray.
Page 1 and 2:
TOSHIBA GA-1120 COLOR GUIDE
Page 3 and 4:
Copyright © 2002 Electronics For I
Page 5:
Proprietary Rights You acknowledge
Page 8 and 9:
viii Contents Starting Calibrator 2
Page 11 and 12:
Introduction xi About this manual T
Page 13:
xiii Key features of ColorWise Colo
Page 16 and 17:
RGB data CMYK data Spot color data
Page 18 and 19:
RGB Separation Output/Simulation 1-
Page 20 and 21:
1-6 GA-1120 Color Management select
Page 22 and 23:
1-8 GA-1120 Color Management If you
Page 24 and 25:
1-10 GA-1120 Color Management The C
Page 26 and 27: 1-12 GA-1120 Color Management are p
Page 28 and 29: 1-14 GA-1120 Color Management • O
Page 30 and 31: Choose ColorWise 1-16 GA-1120 Color
Page 32 and 33: 1-18 GA-1120 Color Management Setti
Page 34 and 35: 1-20 GA-1120 Color Management 3. In
Page 36 and 37: 2-2 Color Calibration An overview o
Page 38 and 39: 2-4 Color Calibration Output profil
Page 40 and 41: 2-6 Color Calibration Starting Cali
Page 42 and 43: Calibration methods appear here 2-8
Page 44 and 45: 2-10 Color Calibration Restoring de
Page 46 and 47: 2-12 Color Calibration 8. Click Mea
Page 48 and 49: 2-14 Color Calibration Calibrating
Page 50 and 51: Indicator light Sample aperture (un
Page 52 and 53: 2-18 Color Calibration In the Paper
Page 54 and 55: 2-20 Color Calibration When the pat
Page 56 and 57: 2-22 Color Calibration 5. Choose th
Page 58 and 59: 2-24 Color Calibration Calibrating
Page 60 and 61: 2-26 Color Calibration TO REMOVE CA
Page 62 and 63: 3-2 ColorWise Pro Tools NOTE: If yo
Page 64 and 65: 3-4 ColorWise Pro Tools 4. Click OK
Page 66 and 67: 3-6 ColorWise Pro Tools TO BACK UP
Page 68 and 69: 3-8 ColorWise Pro Tools TO DEFINE A
Page 70 and 71: 3-10 ColorWise Pro Tools Simulation
Page 72 and 73: 3-12 ColorWise Pro Tools 4. For a s
Page 74 and 75: A curve with this shape makes a col
Page 78 and 79: 3-18 ColorWise Pro Tools TO CORRECT
Page 80 and 81: 3-20 ColorWise Pro Tools 8. In the
Page 82 and 83: 3-22 ColorWise Pro Tools Color Setu
Page 85 and 86: Appendix A: Color Measurement Instr
Page 87 and 88: Unused connector A-3 Color Measurem
Page 89 and 90: A-5 Color Measurement Instruments 6
Page 91 and 92: A-7 Color Measurement Instruments 7
Page 93 and 94: Unused connector Connect to compute
Page 95: A-11 Color Measurement Instruments
Page 98 and 99: B-2 Importing density measurements
Page 101 and 102: Index A Absolute Colorimetric rende
Page 103 and 104: I-3 Index calibration sets for 2-3,
show all

11-12 GA-1120 Color Management - Toshiba

Create successful ePaper yourself

Delete template?

Save as template?