Plattform för bilddatabaser - Kungliga biblioteket
Plattform för bilddatabaser - Kungliga biblioteket
Plattform för bilddatabaser - Kungliga biblioteket
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
MÅTT<br />
Betz 3.D2.1. General rules<br />
Generally, the statement of dimension shows the height x width. The side for height and the side for width<br />
are determined with references to the position in which the image would be viewed. Height is always<br />
expressed first.<br />
KRS 8.5D1. För allt bildmaterial utom bildband och stereobilder anges höjd och bredd avrundade uppåt till<br />
närmaste hela centimetertal. För bildband och stereobilder, se 8.5D2 och 8.5D3. För ytterligare anvisningar<br />
rörande mått <strong>för</strong> originalkonstverk, smådior, tekniska ritningar, stordior och väggplanscher, se 8.5D4 -<br />
8.5D6. (…)<br />
KRS 8.5D4. Originalkonstverk, grafiska blad, konstreproduktioner, stordior.<br />
Ange höjd och bredd <strong>för</strong> objektet utan ram och montering (Se även 8.7B10.).<br />
Betz 3D3.1. For single drawings and planographic and relief prints, generally record the dimensions of the<br />
pictorial area, specified as such. If desirable, record the dimensions of the pictorial area including printed<br />
text. For singel intaglio prints, record the dimensions of the plate mark (see also 3D5). In any case, precede<br />
the dimension by the aspect that has been measured, that is, ”image,” ”image and text,” ”plate mark,” or<br />
”sheet.”<br />
Betz 3D5. Intaglio prints on trimmed sheets or with eradicated plate marks<br />
When a sheet has been cut on or inside the plate mark subsequent to the creation of an intaglio print or the<br />
plate mark is indistinguishable, give the dimensions of the sheet and explain in a note.<br />
KRS 8.5D6. Tekniska ritningar och väggplanscher.<br />
Ange höjd och bredd i utbrett och (i tillämpliga fall) sammanvikt skick.<br />
Betz 3D4.1. For circular shapes, give the diameter, specified as such. Use the abbreviation ”diam.”<br />
Betz 3D4.2. For oval shapes, give the major and minor axes, specified as ”oval.”<br />
Betz 3.D4.3. For an irregular shape, measure by squaring it off at the greatest points with two transparent<br />
triangles or strips of plastic. Use the abbreviation ”irreg.” and, if desirable, whatever word or phrase describes<br />
the shape.<br />
PRAXIS<br />
Är objektets mått under 10 cm i någon ledd anges det exakta måttet i mm. Det är alltid största höjd och<br />
bredd som anges.<br />
Gravyrer (t.ex. Historiska planscher)<br />
I enlighet med Betz anges plåtens avtryck <strong>för</strong> gravyrer. Ex. plåt 21 x 32 cm. Dessutom bör arkets storlek<br />
anges enligt konstruktionen: plåt 21 x 32 cm, på ark 24 x 36 cm. Detta gäller om arket är ursprungligt,<br />
annars är det att se som en montering.<br />
Första bibliotek anger sitt exemplars arkmått, skulle nästa biblioteks exemplars mått skilja sig väsentligt<br />
från detta mått läggs detta i en lokal anmärkning.<br />
99<br />
Litografier (t ex topografiska planscher)<br />
Arkets mått om det är ursprungligt.<br />
Även här gäller att <strong>för</strong>sta katalogiserande bibliotek anger sitt mått osv. (se ovan)