S90 XS/S70 XS Reference Manual - zZounds.com
S90 XS/S70 XS Reference Manual - zZounds.com
S90 XS/S70 XS Reference Manual - zZounds.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Vel Sens Offset (Velocity Sensitivity Offset)<br />
Determines the amount by which played velocities are adjusted for the actual resulting velocity effect. This lets you raise<br />
or lower all velocities by the same amount—allowing you to automatically <strong>com</strong>pensate for playing too strongly or too<br />
softly. If the result is 1 or less, the value is set to 1. If the result is higher than 127, the value is set to 127.<br />
Settings: 0 – 127<br />
When Depth = 64 and Offset =32 When Depth = 64 and Offset =96 When Depth = 64 and Offset =64<br />
127<br />
Actual resulting<br />
velocity<br />
(affecting the tone<br />
generator)<br />
3 Arpeggio<br />
Arp Sw (Arpeggio Switch)<br />
Determines whether Arpeggio is on or off. You can also turn the Arpeggio<br />
Switch on/off from the front panel with the [ARP ON/OFF] button.<br />
Settings: off, on<br />
Arp Select (Arpeggio 1 – 5 Select)<br />
Select one of “ARP1” – “ARP5.” The 8th note icon shown in the settings indicates that one of the Arpeggio Types (other<br />
than “off”) is selected for the Arpeggio. When the Arpeggio/Effect Function is set to “ARP SELECT,” you can select Arp<br />
1 – 5 via the Function buttons.<br />
Settings: Arp 1 – Arp 5<br />
Arp Edit (Arpeggio Edit)<br />
Determines how the item being edited will <strong>com</strong>monly affect all five Arpeggios assigned to each Voice.<br />
Arp Sw (Arpeggio Switch)<br />
Determines whether Arpeggio is on or off. This parameter is same as the “Arp Select” on the Arp Select display in the<br />
Voice Edit.<br />
Settings: off, on<br />
Arp Hold (Arpeggio Hold)<br />
When this is set to “on,” the Arpeggio cycles automatically, even if you release your fingers from the keys, and it<br />
continues to cycle until the next key is pressed.<br />
Settings: sync-off (see below), off, on<br />
NOTE: You can obtain the same result by receiving the Control Change “SUSTAIN” (Control #64) when “Arp Sw” is set to on.<br />
Arp MIDI Out Sw (Arpeggio MIDI Output Switch)<br />
When this is set to on, Arpeggio playback data is output from the MIDI terminal.<br />
Settings: off (not output), on (output)<br />
Arp Transmit Ch (Arpeggio Transmit Channel)<br />
Determines the MIDI transmit channel for Arpeggio playback data. When the parameter is set to “kbd-ch,” the transmit<br />
channel is set to the same MIDI channel as the “Keyboard Transmit Ch” (page 137) in Utility MIDI display.<br />
Settings: 1 – 16, kbd-ch (Keyboard Channel)<br />
127<br />
Actual resulting<br />
velocity<br />
(affecting the tone<br />
generator)<br />
0 64 127<br />
0 64 127<br />
0 64 127<br />
Velocity with which you play a note Velocity with which you play a note<br />
Velocity with which you play a note<br />
sync-off When set to “sync-off,” the Arpeggio playback continues to run silently, even when you release the keys. Pressing any key turns the<br />
Arpeggio playback on again.<br />
<strong>Reference</strong> <strong>Manual</strong><br />
127<br />
Actual resulting<br />
velocity<br />
(affecting the tone<br />
generator)<br />
<strong>Reference</strong><br />
Basic Structure<br />
Voice<br />
Performance<br />
Multi<br />
SEQ Play<br />
Master<br />
Remote<br />
File<br />
Audio Rec/Play<br />
Utility<br />
Performance<br />
Play<br />
Mixing<br />
Edit Select<br />
Common Edit<br />
Name<br />
Play Mode<br />
Arpeggio<br />
Controller<br />
Filter / EG<br />
EQ<br />
Effect<br />
Parameter<br />
A/D Out<br />
A/D FX<br />
Parameter<br />
Part Edit<br />
Voice<br />
Play Mode<br />
Arpeggio<br />
Arp Edit<br />
Arp 1-5 Type<br />
Filter / EG<br />
3 Band EQ<br />
Rcv Sw<br />
FX Send<br />
Job Select<br />
Recall<br />
Bulk<br />
Copy<br />
Initialize<br />
Supplementary Info.<br />
Appendix<br />
84