AR-M237 AR-M277 - Pitney Bowes Canada

More documents

Recommendations

Info

Connectors Caution: This connector is only intended for service purposes. Any connection to this terminal may cause malfunctions of the copy machine. Instruction for service technician: The cable length for the service terminal has to be less than 10 feet (3 m). RSPF connector Finisher connector Parallel connector USB connector
For users in the USA This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Shielded cables must be used with this equipment to maintain compliance with standard. BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WAR- RANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection, Sharp extends a limited warranty to each of its authorized dealers and, in turn, requires each of its authorized dealers to extend its own warranty to you on terms that are no less favorable than those given to the dealer by Sharp. You should be aware, however, that Sharp does not itself extend any warranties, either express or implied, directly to you, the end-user, and no one is authorized to make any representations or warranties on behalf of Sharp. Specifically, SHARP DOES NOT EXTEND TO YOU, THE END-USER, ANY EX- PRESS WARRANTY OR ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN CON- NECTION WITH THE HARDWARE, SOFTWARE OR FIRMWARE EMBODIED IN, OR USED IN CONJUNCTION WITH THIS PRODUCT. Sharp is not responsible for any damages or loss, either direct, incidental or consequential, which you, the end-user, may experience as a result of your purchase or use of the hardware, software or firmware embodied in or used in conjunction with this Product. Your sole remedy, in the event that you encounter any difficulties with this Product, is against the authorized dealer from which you purchased the Product. AR-M237 Digital Multifunctional System AR-M277 Digital Multifunctional System NOTICE for users in the USA In the event that this authorized dealer does not honor its warranty commitments, please contact the General Manager, Business Products Group, Sharp Electronics Corporation, Sharp Plaza, Mahwah, NJ 07430-2135, so that Sharp can try to help assure complete satisfaction of all the warranty rights to which you are entitled from the authorized dealer.
Page 1 and 2:
MODEL AR-M237 AR-M277 DIGITAL MULTI
Page 3 and 4:
CONTENTS CAUTIONS..................
Page 5 and 6:
CAUTIONS Follow the cautions below
Page 7 and 8:
ENVIRONMENTAL INFORMATION As an ENE
Page 9 and 10:
MAIN FEATURES High-speed laser copy
Page 11 and 12:
Interior 15 16 17 18 19 20 21 22 23
Page 13 and 14:
TOUCH PANEL Using the touch panel [
Page 15 and 16:
POWER ON AND OFF The power switch i
Page 17 and 18:
LOADING PAPER When a tray runs out
Page 19 and 20:
LOADING PAPER BEFORE USING THE MACH
Page 21 and 22:
BEFORE USING THE MACHINE CHANGING A
Page 23 and 24:
2 Chapter 2 COPY FUNCTIONS This cha
Page 25 and 26:
COPYING FROM THE RSPF 1 2 3 4 Note
Page 27 and 28:
Copying originals of mixed length (
Page 29 and 30:
AUTOMATIC TWO-SIDED COPYING Two ori
Page 31 and 32:
EXPOSURE ADJUSTMENT SELECTING THE O
Page 33 and 34:
MANUAL RATIO SELECTION There are fo
Page 35 and 36:
4% 0% 4 5 6 Touch the [X] key. X Y
Page 37 and 38:
3 Chapter 3 CONVENIENT COPY FUNCTIO
Page 39 and 40:
STAPLE SORT (when the finisher (AR-
Page 41 and 42:
SPECIAL MODES When the [SPECIAL MOD
Page 43 and 44:
MARGIN SHIFT COPY CONVENIENT COPY F
Page 45 and 46:
DUAL PAGE COPY CONVENIENT COPY FUNC
Page 47 and 48: JOB BUILD MODE CONVENIENT COPY FUNC
Page 49 and 50: ORIGINAL SIZE CONVENIENT COPY FUNCT
Page 51 and 52: L 1 2 Touch the key and then touch
Page 53 and 54: 4 Chapter 4 USER SETTINGS CUSTOM SE
Page 55 and 56: SETTINGS Total count The total page
Page 57 and 58: EXECUTING A JOB PROGRAM S 1 2 Press
Page 59 and 60: 5 Chapter 5 TROUBLESHOOTING AND MAI
Page 61 and 62: SELECTED PAPER TRAY IS OUT OF SERVI
Page 63 and 64: Original size is not selected autom
Page 65 and 66: Image quality problems TROUBLESHOOT
Page 67 and 68: MISFEED IN THE RSPF 1 Remove the mi
Page 69 and 70: 4 Close the front cover and side co
Page 71 and 72: MISFEED IN THE LOWER PAPER TRAY TRO
Page 73 and 74: 3 4 5 6 If staple sort copying is b
Page 75 and 76: STAPLE CARTRIDGE REPLACEMENT (when
Page 77 and 78: CLEANING THE MACHINE DOCUMENT GLASS
Page 79 and 80: FINISHER (AR-FN5N) PERIPHERAL DEVIC
Page 81 and 82: STORAGE OF SUPPLIES Standard suppli
Page 83 and 84: Gradation Scanning: 256 Printing: 2
Page 85 and 86: MATERIAL SAFETY DATA SHEET Data Rev
Page 87 and 88: MATERIAL SAFETY DATA SHEET Data Rev
Page 89 and 90: MATERIAL SAFETY DATA SHEET Data Iss
Page 91 and 92: MATERIAL SAFETY DATA SHEET Data Iss
Page 93 and 94: H Handles .........................
Page 95 and 96: Preparations Bypass tray, loading p
Page 97: MEMO
show all

AR-M237 AR-M277 - Pitney Bowes Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?