Price List July 2012 - Knoll

Power distribution components
2+2 Base Raceway
four circuit, eight-wire raceway for panels
power rails and connector
AutoStrada
description type w d h pattern no. list price
Power rail for panel base 24 panel 6 2 2 RR3-E24 $145.
30 panel 12 2 2 RR3-E30NS 160.
36 panel 18 2 2 RR3-E36NS 175.
42 panel 24 2 2 RR3-E42NS 183.
48 panel 30 2 2 RR3-E48NS 191.
60 panel 42 2 2 RR3-E60-4 290.
66 panel 48 2 2 RR3-E66-4 306.
72 panel 54 2 2 RR3-E72-4 327.
Power connector* Straight 16 1 /2 2 2 RR3-EPC24 84.
18 1 /2 2 2 RR3-EPCSM 84.
20 1 /4 2 2 RR3-EPCM 84.
Use RR3-EPC24 for straight 24 to 24 wide panel.
Use RR3-EPCS for straight 24 to any other width panel and for 30 to 30 wide panels.
Use RR3-EPC for all other straight power connection configurations.
Through post 19 2 2 RR3-EPCP24 84.
21 2 2 RR3-EPCPSM 84.
22 3 /4 2 2 RR3-EPCPM 84.
Use RR3-EPCP24 for through post 24 to 24 wide panels.
Use RR3-EPCPS for through post 24 to any other width panel and for 30 to 30 wide
panels.
Use RR3-EPCP for all other through post power connection configurations.
Panels
Duplex outlets, black Circuit A RR3-DA 40.
Circuit B RR3-DB 40.
Circuit X RR3-DX 40.
Circuit Y RR3-DY 40.
Duplex outlets, orange Circuit X RR3-DXO 45.
Circuit Y RR3-DYO 45.
Data Shield 1 pair RR3-DATSHD 28.
Order Code
Example: RR3-E-24
RR3 Reff raceway
E Eight wire 2+2
24 for 24 panel
Specification Information
Reff 2+2 Raceway is a four-circuit,
eight-wire modular power
distribution system for use in Reff
panels. 2+2 Raceway components
distribute two 20-amp convenience
circuits (A and B) with neutral and
ground, and two protected 20-amp
circuits (X and Y) with separate
neutral and ground. In Canada
circuits carry 15 amp load resting.
Specify the suffix ‘‘RF’’ after the
power rail pattern number for panels
manufactured before June 1996.
131
Application Notes
Power rails are the primary power
distribution component of the Reff
2+2 Raceway. Each rail provides
outlet mounting positions on both
sides and receptacles for two
branching power connectors at each
end. Center supports permit lay-in
cabling from either side of the
raceway.
Rail for 24 wide panel accepts one
duplex outlet or power infeed
centered on each side. Rails for 30
to 48 panels accept two outlets (or
one outlet and one infeed) on each
side. 60,66 and 72W panels
accept four duplex outlets per side.
Duplex outlets are preconfigured to
access one of the four circuits, A, B,
X, Y, and snap into any standard
outlet location. Duplexes on circuits
X and Y may be specified in orange
to signify protected circuits for
electronic equipment.
Power connectors transmit power
between adjacent powered panels.
Specify straight power connector for
straight connections and
through-post power connector when
passing in a 90° or straight through
a T, X or L post connection.
Power connectors are enclosed in
steel flexible conduit.
*Power connectors must be
specified according to the panel
widths in the specified orientation.
If separation of cabling and
electrical wires is required, a data
shield can be attached below the
power rail. Data Shields are field
installed.