Price List July 2012 - Knoll

Power distribution components
2+2 Base Raceway
four circuit, eight-wire raceway for panels
jumpers and infeed
AutoStrada
description type w d h pattern no. list price
Jumper 18 panel 38 2 2 RR3-EJ18 $105.
20 panel 40 2 2 RR3-EJ20 105.
24 panel 44 2 2 RR3-EJ24 113.
30 panel 50 2 2 RR3-EJ30 121.
36 panel 56 2 2 RR3-EJ36 132.
42 panel 62 2 2 RR3-EJ42 138.
48 panel 68 2 2 RR3-EJ48 145.
54 panel run 76 1 /2 2 2 RR3-EJ54P 152.
60 panel run 82 1 /2 2 2 RR3-EJ60P 160.
66 panel run 88 1 /2 2 2 RR3-EJ66P 168.
72 panel run 94 1 /2 2 2 RR3-EJ72P 175.
78 panel run 100 1 /2 2 2 RR3-EJ78P 183.
84 panel run 106 1 /2 2 2 RR3-EJ84P 191.
90 panel run 112 1 /2 2 2 RR3-EJ90P 200.
96 panel run 118 1 /2 2 2 RR3-EJ96P 207.
Extended jumper (through one post) 18 + post 40 1 /2 2 2 RR3-EJ18P 105.
20 + post 42 1 /2 2 2 RR3-EJ20P 105.
24 + post 46 1 /2 2 2 RR3-EJ24P 113.
30 + post 52 1 /2 2 2 RR3-EJ30P 121.
36 + post 58 1 /2 2 2 RR3-EJ36P 132.
42 + post 64 1 /2 2 2 RR3-EJ42P 138.
48 + post 70 1 /2 2 2 RR3-EJ48P 145.
Power infeeds Ceiling power cable infeed. Eight-wire RR3-EPVR 290.
Hardwire infeed (NYC) one direction RR3-EPNY1 212.
Hardwire infeed (NYC) two directions RR3-EPNY2 318.
Panel base end feed RR3-REPI 252.
Panel base side infeed RR3-EPI 252.
Surge suppressors RR3-SP-(A,B,X,Y) 183.
Order Code
Example: RR3-EPVR
RR3 Reff raceway
E Eight wire 2+2
P power infeed
VR for vertical raceway
Specification Information
Reff 2+2 Raceway is a four-circuit,
eight-wire modular power
distribution system for use in Reff
panels. 2+2 Raceway components
distribute two 20-amp convenience
circuits (A and B) with neutral and
ground, and two 20-amp circuits (X
and Y) with separate neutral and
ground.
For use in Canada, all circuits are
CGA rated 15 amp capacity.
Note:
For NYC hardwire infeeds specify
bracket height: 4,5,or6H.
Beltway panels can use jumpers at
the panel base in a straight run or
around a corner.
132
Application Notes
Jumpers pass power through the
raceway of panels that do not
require power access to the next
available power rail. Jumpers only
connect to power rails. Jumpers 18
to 48 are available standard or
extended. Extended jumpers should
be specified when passing through a
panel and a post. Jumpers 54 to 96
wide can be used with or without a
post application. Extended jumpers
and jumpers 54 to 96 wide can
only pass through panels and one
post.
Power infeeds connect building
power supply to a cluster of
interconnected power rails. Panel
base infeed snaps into any outlet
position in rail, and includes 6 foot
liquid-tight conduit and pigtail for
connection to floor or wall electrical
box. Ceiling infeeds include up to
13 pigtail for connection
into panel base through power pole
adjacent to panel with power rail.
Power pole and post must be
ordered separately.
Hardwire infeed, used in all New
York City installations, includes
junction box that mounts within
non-powered panel base (any width
30 or greater). Electrical contractor
supplies watertight conduit from
building power supply to panel and
trims power connectors to length.
RR3-EPNY2 includes two power
connectors to power panels on both
sides of infeed panel; RR3-EPNY1
includes only one power connector.
Cable sizes are nominal. Use the
‘‘type’’ column to specify the
required cable for your panel.