Price List July 2012 - Knoll

Specifications
Specifying Crinion Open Table
AutoStrada
Crinion Open Tables are comprised
of worksurfaces, table base
assemblies, power components and
screens.
Worksurfaces
Individual worksurfaces are
available in four standard widths
(48,60,72,96) and three depths
(nominal 24,30,36), which may
be combined to form single-sided or
dual-sided groups of two to ten or
more positions.
Worksurface edge options
Worksurfaces are 1 1 /4 thick, with
three front edge options:
Tapered edge, laminate, veneer or
mixed.
Square edge, veneer
Postformed edge, laminate only
Power and accessory options
Worksurfaces may be specified with
hinged power access door and
continuous 1 /2 cord drop, or edge
grommet and continuous cord drop,
or just cord drop.
Hinged power access door is 24W
and 5D, centered on worksurface
width. Door hinges toward user for
continuity between access opening
and cord drop.
Any worksurface (except end
counters) accepts clamp on
KnollExtra accessories such as flat
screen monitor arm or task light.
Other worksurface types
End counters have front edge detail
on side edges as well and are
designed to extend dual tables 24 or
30 beyond the endleg. End counters
also include 3 wide center grommet.
Extended end counters are 36D
surfaces with center grommet or
hinged power access door. Base of
the table must be extended 12 under
the back of each extended end
counter (although top channels
should be specified only as wide as
the worksurfaces on each side of the
table).
All end counters must be supported
by end counter cantilevers and
endlegs for end counters.
Worksurface heights
Fixed height cantilevers support
worksurfaces at 28 1 /2H, with 27
clear below the top (except directly
below cantilevers).
Adjustable height cantilevers enable
worksurfaces to be independently set
at 27,27 3 /4,28 1 /2,29 1 /4,or30H.
Open Table base assemblies
Complete base assemblies simplify
specifications for most common
configurations of dual or single-sided
open tables. Base assemblies include
top channels and end caps, beams,
end legs and intermediate legs
(where required), trusses and top
channel supports, cantilever
brackets (specify fixed or adjustable
height) and midspan supports.
Specify worksurfaces, screens, power
components, cable trays and
accessories separately.
Complete base assemblies are
available for the following typical
tables, combinations of 60 or 72
worksurfaces.
Single-sided or dual, 24D, 30D, or
36D, with continuous beam span
between end legs
10 W two/four positions 60W
12 W two/four positions 72W
15 W three/six positions 60W
Single sided or dual 24D, 30D, or
36D, with intermediate leg
18 W three/six positions 72W
20 W four/eight positions 60W
24 W four/eight positions 72W
25 W five/ten positions 60W
Open Table base components
Base assemblies may also be
specified by individual components
to create configurations other than
those listed above, or to create tables
with end counters or frameless glass
add ups.
In addition to worksurfaces Open
tables require top channel, starter
beams for spans up to 15, extension
beams for additional spans of 4 to
15, intermediate legs every 16 or
less, two end legs, trusses at every
worksurface junction and at each end
leg. Adjustable tables require two
cantilevers per worksurface (or three
for 96W). Fixed height tables may
be supported by a fixed height
cantilever at each end, shared
cantilevers at each worksurface joint,
and a midspan support bracket at the
center of each worksurface greater
than 48 wide. For 96W
worksurfaces the midspan support
should be a 24D cantilever.
Power components, cable trays and
screens are optional.
Power distribution
Optional modular raceway
distributes 2+2 four circuit or 3+3
six circuit configuration from a single
point of supply. Bundles of cables
can be managed from the floor in a
cable infeed shroud located at any
intermediate leg. Raceway provides
power outlets and
data/communications outlet openings
on one or both sides, accessed
through hinged access doors in
worksurfaces or from under table.
Specify 30 raceway for two duplex
outlets each side or 42 raceway for
four duplex outlets each side. Duplex
outlets, power infeed and jumpers
between raceways must be specified
separately.
Specify compact power module for
outlets under extended end counters.
Privacy screens
There are four screen options for
Crinion Open Table.
The standard screens are 14H (42
horizon) or 21H (49 horizon) in
acrylic, slat wall or combination
surfaces. Center screens include
mounting hardware to attach to the
standard top channel. Center screens
are available full width, 48,60 or
72, or shorter by 1 to leave space at
either end of the table for a dual end
screen. Side screens attach to the
front and back of a worksurface at
any point other than at a hinged
access door. Mounting brackets are
specified separately to correspond to
each worksurface edge detail. Dual
end screens span across the end of a
table (or above an end counter) from
worksurface front edges.
Frameless glass add ups are
available in 12 height only, 48,60,
and 72W. Add ups can only mount
to a top channel for frameless glass
add ups, which may be at the center
of a dual table or back of a
single-sided table specified by
components.
Original Crinion privacy screens are
12Hor19H (41 or 48 horizons)
and mount to a standard top channel
only.
Morrison Network fabric screens
(15Hor22H) can also be mounted
to the standard top channel with
Crinion Open Table mast kit.
Accessories and storage
All Crinion worksurfaces accept
clamp base KnollExtra flat screen
monitor arms and task lights at any
point except behind the hinged
power access door. Worksurfaces also
accept suspended accessories like
adjustable keyboard supports,
BackPack center file or keyboard
drawers, or CPU holders. Beam
location under most tables prevents
pedestals deeper than 20
underneath. However 36D tops can
be planned on 30D table bases to
create additional kneespace depth
and room for 24D pedestals.
Crinion Open Table file tops are
available for 27H Calibre files
positioned perpendicular to the table
to act as returns. Tapered front and
back edges assure consistent detail
with tapered worksurface edges. File
tops are also available for pairs of
files and back to back files.
252