Price List July 2012 - Knoll

Power distribution components
3+3 Base Raceway
six circuit, ten-wire raceway for panels
jumpers and infeed
AutoStrada
description type w d h pattern no. list price
Jumper 18 panel 38 2 2 RR3-TJ18 $121.
20 panel 40 2 2 RR3-TJ20 121.
24 panel 44 2 2 RR3-TJ24 132.
30 panel 50 2 2 RR3-TJ30 138.
36 panel 56 2 2 RR3-TJ36 145.
42 panel 62 2 2 RR3-TJ42 160.
48 panel 68 2 2 RR3-TJ48 175.
54 panel run 76 1 /2 2 2 RR3-TJ54P 183.
60 panel 82 1 /2 2 2 RR3-TJ60P 191.
66 panel run 86 1 /2 2 2 RR3-TJ66P 200.
72 panel run 94 1 /2 2 2 RR3-TJ72P 207.
78 panel run 100 1 /2 2 2 RR3-TJ78P 212.
84 panel run 106 1 /2 2 2 RR3-TJ84P 232.
90 panel run 112 1 /2 2 2 RR3-TJ90P 237.
96 panel run 118 1 /2 2 2 RR3-TJ96P 243.
Extended jumper 18 + post 40 1 /2 2 2 RR3-TJ18P 121.
20 + post 46 1 /2 2 2 RR3-TJ20P 121.
24 + post 46 1 /2 2 2 RR3-TJ24P 132.
30 + post 52 1 /2 2 2 RR3-TJ30P 138.
36 + post 58 1 /2 2 2 RR3-TJ36P 145.
42 + post 64 1 /2 2 2 RR3-TJ42P 160.
48 + post 70 1 /2 2 2 RR3-TJ48P 175.
Power infeeds Ceiling power cable infeed. Ten-wire RR3-TPVR 351.
Hardwire infeed (NYC) one direction ** RR3-TPNY1 243.
Hardwire infeed (NYC) two directions ** RR3-TPNY2 351.
Panel base end feed RR3-RTPI 290.
Panel base side infeed RR3-TPI 290.
Surge suppressors * RR3-SP-(A, B, C, X, Y, Z) 183.
* Select which circuit needs protecting and order the specified surge processor.
** For RR3-TPNY1 and RR3-TPNY2 specify base height of panel for NYC.
Order Code
Example: RR3-TPVR
RR3 Reff raceway
T Ten wire 3+3
P power infeed
VR for vertical raceway
Specification Information
Reff 3+3 Raceway is a six-circuit,
ten-wire modular power distribution
system for use in Reff panels. 3+3
Raceway components distribute
three 20-amp convenience circuits
(A, B and C) with neutral and
ground, and three 20-amp circuits
(X, Y and Z) with separate neutral
and ground.
In Canada, circuits carry a 15 amp
load rating.
Power infeeds connect building
power supply to a cluster of
interconnected power rails. Panel
base infeed snaps into any outlet
position in rail, and includes 6 foot
liquid-tight conduit and pigtail for
connection to floor or wall electrical
box. Ceiling infeeds include up to
13 pigtail for connection into panel
base through standard power pole.
Power pole and post must be
ordered separately.
134
Hardwire infeed, used in all New
York City installations, includes
junction box that mounts within
non-powered panel base (any width
30 or greater). Electrical contractor
supplies watertight conduit from
building power supply to panel and
trims power connectors to length.
RR3-TPNY2 includes two power
connectors to power panels on both
sides of infeed panel; RR3-TPNY1
includes only one power connector.
Note:
For NYC hardwire infeeds specify
bracket height: 4,5,or6H.
Application Notes
Jumpers pass power through the
raceway of panels that do not
require power access to the next
available power rail. Jumpers only
connect to power rails. Jumpers 18
to 48 are available standard or
extended. Extended jumpers should
be specified when passing through a
panel and a post. Jumpers 54 to 96
wide can be used with or without a
post application. Extended jumpers
and jumpers 54 to 96 wide can
only pass through panels and one
post.
Cable sizes are nominal. Use the
‘‘type’’ column to specify the
required cable for your panel.
Beltway panels can use jumpers at
the panel base in a straight run or
around a corner.