Sun Fire V445 Server Administration Guide - SCN Research

More documents

Recommendations

Info

5. To verify the network settings, type: sc> shownetwork 6. Log out of the ALOM system controller session. To connect through the network management port, use the telnet command to the IP address you specified in Step 3 of the preceding procedure. Accessing the System Console With a Terminal Server The following procedure assumes that you are accessing the system console by connecting a terminal server to the serial management port (SERIAL MGT) of the Sun Fire V445 server. ▼ To Access the System Console With a Terminal Server Through the Serial Management Port 1. Complete the physical connection from the serial management port to your terminal server. The serial management port on the Sun Fire V445 server is a data terminal equipment (DTE) port. The pinouts for the serial management port correspond with the pinouts for the RJ-45 ports on the Serial Interface Breakout Cable supplied by Cisco for use with the Cisco AS2511-RJ terminal server. If you use a terminal server made by another manufacturer, check that the serial port pinouts of the Sun Fire V445 server match those of the terminal server you plan to use. If the pinouts for the server serial ports correspond with the pinouts for the RJ-45 ports on the terminal server, you have two connection options: ■ Connect a serial interface breakout cable directly to the Sun Fire V445 server. See “Using the Serial Management Port” on page 39. ■ Connect a serial interface breakout cable to a patch panel and use the straightthrough patch cable (supplied by Sun) to connect the patch panel to the server. 42 Sun Fire V445 Server Administration Guide • August 2006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Terminal server Straight-through cable 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Patch panel Patch cable to serial management port Sun Fire V445 server FIGURE 2-4 Patch Panel Connection Between a Terminal Server and a Sun Fire V445 Server If the pinouts for the serial management port do not correspond with the pinouts for the RJ-45 ports on the terminal server, you need to make a crossover cable that takes each pin on the Sun Fire V445 server serial management port to the corresponding pin in the terminal server’s serial port. TABLE 2-3 shows the crossovers that the cable must perform. TABLE 2-3 Pin Crossovers for Connecting to a Typical Terminal Server Sun Fire V445 Serial Port (RJ-45 Connector) Pin Pin 1 (RTS) Pin 2 (DTR) Pin 3 (TXD) Pin 4 (Signal Ground) Pin 5 (Signal Ground) Terminal Server Serial Port Pin Pin 1 (CTS) Pin 2 (DSR) Pin 3 (RXD) Pin 4 (Signal Ground) Pin 5 (Signal Ground) Chapter 2 Configuring the System Console 43
Page 1 and 2:
Sun Fire V445 Server Administratio
Page 3 and 4:
Contents Preface xxi 1. System Over
Page 5 and 6:
Ways of Reaching the sc> Prompt 32
Page 7 and 8:
Memory Interleaving 70 Independent
Page 9 and 10:
▼ To Enable the Hardware Watchdog
Page 11 and 12:
Reference for Estimating System Boo
Page 13 and 14:
About Sun Management Center 204 How
Page 15 and 16:
Reference for Clearance and Service
Page 17 and 18: Figures FIGURE 1-1 Front Panel Feat
Page 19 and 20: Tables TABLE 1-1 Sun Fire V445 Serv
Page 21 and 22: Preface The Sun Fire V445 Server Ad
Page 23 and 24: Typographic Conventions TABLE P-1 T
Page 25 and 26: http://www.sun.com/hwdocs/feedback
Page 27 and 28: CHAPTER 1 System Overview This chap
Page 29 and 30: TABLE 1-1 Feature Sun Fire V445 Ser
Page 31 and 32: RAID 0,1 Internal Hard Drives Inter
Page 33 and 34: technology enables Sun systems to a
Page 35 and 36: For information about front panel c
Page 37 and 38: For hard disk drive indicator descr
Page 39 and 40: SAS Disk Drives The system has up t
Page 41 and 42: Locating Back Panel Features The il
Page 43 and 44: PCI0 PCI1 PCI6 PCI7 PCI2 PCI3 PCI5
Page 45 and 46: Serial Management Port The serial m
Page 47 and 48: Reliability, Availability, and Serv
Page 49 and 50: CHAPTER 2 Configuring the System Co
Page 51 and 52: TABLE 2-1 Ways of Communicating Wit
Page 53 and 54: Default System Console Connection T
Page 55 and 56: Access Through the Network Manageme
Page 57 and 58: About the sc> Prompt The ALOM syste
Page 59 and 60: About the ok Prompt A Sun Fire V445
Page 61 and 62: L1-A (Stop-A) Keys or Break Key Whe
Page 63 and 64: System Console ok NET MGT or SERIAL
Page 65 and 66: 4. Refer to TABLE 2-2 for instructi
Page 67: Note - The network management port
Page 71 and 72: 2. To cause the changes to take eff
Page 73 and 74: 3. In a shell tool window on the Su
Page 75 and 76: Modifying the /etc/remote File This
Page 77 and 78: Accessing the System Console With a
Page 79 and 80: If you have redirected the system c
Page 81 and 82: 6. Obtain the ok prompt. For more i
Page 83 and 84: CHAPTER 3 Powering On and Powering
Page 85 and 86: Powering On the Server Locally Do n
Page 87 and 88: Caution - Applications running on t
Page 89 and 90: the OS to recognize the configurati
Page 91 and 92: If the system encounters a problem
Page 93 and 94: CHAPTER 4 Configuring Hardware This
Page 95 and 96: 1 0 1 0 DIMM group 1 DIMM group 0 F
Page 97 and 98: DIMM Configuration Rules ■ ■
Page 99 and 100: Caution - Although access to the AL
Page 101 and 102: ■ your configuration requires a h
Page 103 and 104: PCI0 PCI1 PCI6 PCI7 PCI3 PCI2 PCI5
Page 105 and 106: About the SAS Backplane The Sun Fir
Page 107 and 108: For additional information, see “
Page 109 and 110: The Solaris Volume Manager software
Page 111 and 112: A power supply can be hot-swapped o
Page 113 and 114: FIGURE 4-7 System Fan Trays and Fan
Page 115 and 116: About the USB Ports The system fron
Page 117 and 118: CHAPTER 5 Managing RAS Features and
Page 119 and 120:
power supplies, fan trays, and USB
Page 121 and 122:
detects the failure and generates a
Page 123 and 124:
(striping with interleaved parity).
Page 125 and 126:
For instructions on connecting to t
Page 127 and 128:
Viewing Environmental Information U
Page 129 and 130:
● From the ALOM system controller
Page 131 and 132:
4. To view console output as the sy
Page 133 and 134:
TABLE 5-1 Device Identifiers and De
Page 135 and 136:
▼ To Enable the Hardware Watchdog
Page 137 and 138:
CHAPTER 6 Managing Disk Volumes Thi
Page 139 and 140:
Sun StorEdge Traffic Manager A newe
Page 141 and 142:
RAID 0 - Disk Striping Disk stripin
Page 143 and 144:
Caution - Creating or restoring a d
Page 145 and 146:
2. Type the following command: # ra
Page 147 and 148:
3. To confirm that you have deleted
Page 149 and 150:
4. To check the status of a RAID re
Page 151 and 152:
Note that while you can use the Sol
Page 153 and 154:
6. To verify that the new disk driv
Page 155 and 156:
CHAPTER 7 Managing Network Interfac
Page 157 and 158:
Attaching a Twisted-Pair Ethernet C
Page 159 and 160:
During installation of the Solaris
Page 161 and 162:
The name of the file you create sho
Page 163 and 164:
CHAPTER 8 Diagnostics This chapter
Page 165 and 166:
TABLE 8-1 Summary of Diagnostic Too
Page 167 and 168:
TABLE 8-2 Component What ALOM Monit
Page 169 and 170:
About Status Indicators For a summa
Page 171 and 172:
■ ■ diag-switch? parameter has
Page 173 and 174:
TABLE 8-3 OpenBoot Configuration Va
Page 175 and 176:
Note that service mode does not cha
Page 177 and 178:
When you are deciding whether to en
Page 179 and 180:
If you specify settings for neither
Page 181 and 182:
If you need to know the approximate
Page 183 and 184:
The following sample shows the firm
Page 185 and 186:
CODE EXAMPLE 8-1 Executing Power On
Page 187 and 188:
System Reset skip_diag System Contr
Page 189 and 190:
TABLE 8-6 Summary of Diagnostic Ope
Page 191 and 192:
4. You can also run all tests, type
Page 193 and 194:
To customize an individual test, yo
Page 195 and 196:
The following is sample output from
Page 197 and 198:
show-devs Command The show-devs com
Page 199 and 200:
Use the following web site to inter
Page 201 and 202:
# fmdump TIME UUID SUNW-MSG-ID Jul
Page 203 and 204:
# fmstat module ev_recv ev_acpt wai
Page 205 and 206:
Using the prtconf Command The prtco
Page 207 and 208:
CODE EXAMPLE 8-7 prtdiag Command Ou
Page 209 and 210:
CODE EXAMPLE 8-7 MB/FT0/F0 TACH oka
Page 211 and 212:
The prtfru command can display this
Page 213 and 214:
CODE EXAMPLE 8-12 prtfru -c Command
Page 215 and 216:
When used with the -p option, this
Page 217 and 218:
▼ To View and Set OpenBoot Config
Page 219 and 220:
Using the probe-ide Command To Conf
Page 221 and 222:
If the kernel hangs and the watchdo
Page 223 and 224:
Error Handling Summary Error handli
Page 225 and 226:
Automatic System Restoration User C
Page 227 and 228:
About SunVTS SunVTS is a software s
Page 229 and 230:
TABLE 8-12 SunVTS Test vmemtest env
Page 231 and 232:
TABLE 8-14 Feature Sun Management C
Page 233 and 234:
Interoperability With Third-Party M
Page 235 and 236:
CHAPTER 9 Troubleshooting This chap
Page 237 and 238:
■ ■ Sun System Handbook - A doc
Page 239 and 240:
About Sun Remote Services Net Conne
Page 241 and 242:
Remote Troubleshooting Capabilities
Page 243 and 244:
core dump directory to another loca
Page 245 and 246:
4. Type the df -k1 command to ident
Page 247 and 248:
APPENDIX A Connector Pinouts This a
Page 249 and 250:
Network Management Connector Diagra
Page 251 and 252:
Reference for the USB Connectors Tw
Page 253 and 254:
APPENDIX B System Specifications Th
Page 255 and 256:
TABLE B-2 Electrical Specifications
Page 257 and 258:
Reference for Clearance and Service
Page 259 and 260:
APPENDIX C OpenBoot Configuration V
Page 261 and 262:
TABLE C-1 OpenBoot Configuration Va
Page 263 and 264:
Index Symbols /etc/hostname file, 1
Page 265 and 266:
dual inline memory modules (DIMMs),
Page 267 and 268:
configuring IP address, 41 configur
Page 269 and 270:
SEAM (Sun Enterprise Authentication
Page 271 and 272:
W watchdog, hardware, See hardware
show all

Sun Fire V445 Server Administration Guide - SCN Research

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?