Telemetry Module MT-102 User's Manual - BlueNote Communications

More documents

Recommendations

Info

8.2.5.7.2. Number of retries Function - defines number of attempts to transmit data via PORT2 in case of unconfirmed (within time defined by transmission Timeout parameter) reception. Data type - number Range - 0…7 Default value - 1 Comments - value 0 results in sending without confirming faultless reception. 8.2.5.7.3. Transmission timeout Function - Defines (in seconds) waiting time for confirmation of data frame reception. Data type - number Range - 0…10 [s] Default value - 2 [s] Comments - This value along with declared Number of retries influences max. time of single data packet transmission. 8.2.5.7.4. Threshold hysteresis Function - Defines hysteresis for alarm thresholds values Data type - number Range - 0,01…100,00 [%] Default value - 5,00 [%] Comments - setting of value of hysteresis adequate to signal variations prevents untimely activations of alarm flags. 8.2.5.7.5. Gas meter address Function - Defines address of gas meter connected to module's PORT 1 Data type - number Range - 0…65535 Default value - 0 Comments - n/a 8.2.5.7.6. Gas meter reading interval Function - Defines (seconds) interval of readings from peripheral device using GazModem protocol for update measurement data. The connection is via PORT 1 Data type - number Range - 0…65535 [s] Default value - 180 [s] Comments - value 0 (zero) forces max. possible frequency of updating. It depends on speed of PORT2 along with size and number of defined mapped spaces. 57
8.2.5.7.7. Number of transmission retries to gas meter Function - defines number of attempts to transmit data via PORT1 in case of unconfirmed (within time defined by Transmission timeout to gas meter parameter) reception. Data type - number Range - 0…7 Default value - 2 Comments - value 0 results in sending without confirming faultless reception. 8.2.5.7.8. Transmission timeout for gas meter Function - Defines (in seconds) waiting time for confirmation of data frame reception at PORT1. Data type - number Range - 0,01…10,00 [s] Default value - 2,00 [s] Comments - This value along with declared Number of transmission retries to gas meter influences max. time of single data packet transmission. 8.2.5.7.9. Number of devices Function - Defines number of declared register spaces (devices) read on PORT2 from peripheral devices operating on M-Bus protocol. Data type - number Range - 1…16 Default value - 1 Comments - n/a 8.2.5.7.10. MC The table defining consecutive data blocks read from peripheral devices attached to PORT2 operating in M-Bus protocol. The table can hold from 1 to 16 independent blocks in one or more devices. 8.2.5.7.10.1. Address 1...16 Function - Defines address of heat meter whose internal parameters shall be read. Data type - number Range - 0…255 Default value - 0 Comments - address 255 means querying stopped 8.2.5.7.10.2. Geographical coordinates format Function - Defines format of geographical coordinates received in NMEA 0183 protocol when writing into registers. 58
Page 1 and 2:
TelemetryModule MT-102 UserManual t
Page 3 and 4:
MT-102 © 2010 Inventia Ltd. Wszelk
Page 5 and 6:
2 8.2. PARAMETER GROUPS ...........
Page 7 and 8:
4 8.2.6.2.1.2.2.6. Alarm HiHi .....
Page 9 and 10: 10.1.6. PORT 2 activity ...........
Page 11 and 12: 1. Introduction Despite the explosi
Page 13 and 14: 4.2. Resources MT-102 module's reso
Page 15 and 16: Transmission parameters are: speed
Page 17 and 18: 4.3.6. MT2MT buffer MT2MT buffer en
Page 19 and 20: As shown by graph, the value at whi
Page 21 and 22: Binary inputs Q1…Q8 - in positive
Page 23 and 24: PORT 2 (RS-232/422/485 - communicat
Page 25 and 26: part. Even with no SIM inserted, th
Page 27 and 28: Properly inserted SIM cards secure
Page 29 and 30: packet routing - useful for unambig
Page 31 and 32: 7.5. Modem mode In this mode, the m
Page 33 and 34: This mode was implemented due to re
Page 35 and 36: Authorized numbers group - contains
Page 37 and 38: NOTICE! Availability of parameters
Page 39 and 40: List - All Unrestricted access for
Page 41 and 42: 8.2.2.12. Use of SMS Function - def
Page 43 and 44: 8.2.3.5. IP assignment Function - s
Page 45 and 46: Range - 0.0.0.0 - 255.255.255.255 D
Page 47 and 48: Comments - The range value defines
Page 49 and 50: Comments - n/a 8.2.5.1.1.2. Data pa
Page 51 and 52: number ID - ID number of device con
Page 53 and 54: 8.2.5.4.2. Delay after error in com
Page 55 and 56: 8.2.5.4.3.7. Force write the whole
Page 57 and 58: Comments - value 0 (zero) forces ma
Page 59: No Current data reading inactive De
Page 63 and 64: 8.2.5.9.2. Data packet delimiter Fu
Page 65 and 66: It is recommended to set filtering
Page 67 and 68: 8.2.6.2.1.2.2.9. Alarm LoLo Functio
Page 69 and 70: 8.2.6.2.2.1. Name Function - allows
Page 71 and 72: Default value - 0 [engineering unit
Page 73 and 74: Comments - Function has no influenc
Page 75 and 76: List - Auto Data collected in Logge
Page 77 and 78: Default value - 0 Comments - n/a 8.
Page 79 and 80: Default value - . Comments - if the
Page 81 and 82: Default value - Bi In 0->1, Bi In 1
Page 83 and 84: 8.2.7.3.2. Number of trials Functio
Page 85 and 86: For remote configuration, it is vit
Page 87 and 88: RS-232 Port Contains number of the
Page 89 and 90: Nie można wyświetlić połączone
Page 91 and 92: and after connecting to the module
Page 93 and 94: The icon on the toolbar performs sa
Page 95 and 96: “If” - defines the condition fo
Page 97 and 98: Detailed description of standard an
Page 99 and 100: Multiply X by Y store result (regis
Page 101 and 102: Mask test This function verifies wh
Page 103 and 104: Both 16 and 32 bit registers can be
Page 105 and 106: get Y: - unit number defines the nu
Page 107 and 108: CAUTION! All variables in Modbus ad
Page 109 and 110: 9.12. Downloding the program After
Page 111 and 112:
9.14.4. 2 pumps alternating action
Page 113 and 114:
The same effect can be obtained in
Page 115 and 116:
9.14.8. Logger program An example o
Page 117 and 118:
10.1.3. GSM status GSM Status LEDs
Page 119 and 120:
10.1.6. PORT 2 activity LED indicat
Page 121 and 122:
10.1.8. SET1, SET2 alarm thresholds
Page 123 and 124:
When GPRS LED is off the module is
Page 125 and 126:
11. Technical data 11.1. General Di
Page 127 and 128:
Analogue inputs AN3 … AN6: Measur
Page 129 and 130:
12. Safety informations 12.1. Worki
Page 131 and 132:
13.1.3.1. Advantages of GPRS techno
Page 133 and 134:
13.2.2. Point to point communicatio
Page 135 and 136:
without decoding of protocol. This
Page 137 and 138:
The value may be variable or consta
Page 139 and 140:
comment: 13.6. Data forma
Page 141 and 142:
13.8. Trigger inputs During operati
Page 143 and 144:
13.10. RM-120 Converter module RM-1
Page 145 and 146:
142 0x0050 AQ1_LoLo AQ1_Lo AQ1_Hi A
Page 147 and 148:
144 0x0388 MT2MT_20 MT2MT_21 9 0 0x
Page 149 and 150:
13.11.3. Analogue inputs space Inpu
Page 151 and 152:
13.11.4. Internal registers space I
Page 153 and 154:
150 0x0267 Dead band threshold AQ8
Page 155 and 156:
0x11E 286 30287 MC2VAR8_H 0x11F 287
Page 157 and 158:
13.11.6. Auxiliary resources for M-
Page 159 and 160:
Offset Type Rx[High,Low] Descriptio
Page 161 and 162:
Start Address hex dec MODBUS Descri
Page 163 and 164:
All values are stored in 2 16 bit r
Page 165:
Address 0x418 (1048) Modbus (41049)
show all

Telemetry Module MT-102 User's Manual - BlueNote Communications

Create successful ePaper yourself

Delete template?

Save as template?