iDEAl EsPRit - Ideal Heating

More documents

Recommendations

Info

FLUE OUTLET 20 17 FLUE EXTENSION DUCTS - continued 1. A maximum of 6 extension ducts for the HE24/ HE30 and a maximum of 3 extension ducts for the HE35 (one suitably cut) plus the standard flue duct may be used together. 2. Flue extensions of greater length than 1m (39") should be supported with the bracket provided, suitably adjusted. Refer to Frames 16 and 24. 3. Only use water as a lubricant during assembly. Do not use mineral based oils. 18 FITTING THE KIT INSTALLATION 16 FLUE EXTENSION DUCTS - For total flue lengths greater than 595mm Pack D Flue extension duct kit contents Extension duct & clamp 1.0m (39") long nm8732 General arrangement Flue duct support Use a maximum of 6m extended flue ONLY (HE24 & 30) Use a maximum of 3m extended flue ONLY (HE35) Because of the flexibility of the telescopic flue terminal it is not always necessary to cut an extension pack. 1. Measure the total flue length from the centre of the boiler outlet to the outside wall. 2. Subtract 70mm from this dimension. 3. Subtract 950mm for each ‘D’ pack to be used. 4. If the remainder Y is 300mm - 525mm this can be taken up 70 by the adjustment in the telescopic flue. 5. If the remainder Y is 525mm - 950mm it will be necessary to cut a ‘D’ pack to 400mm. esp8940 950 Flue support cutting aid (shown folded up) Wall plugs - 4 off No. 10 x2" wood screw - 4 off Boiler nm8762 Flue length Extension flue Standard flue Terminal grille Note. Side flue shown 6. If the remainder Y is less than 300mm, shorten the previous ‘D’ pack to 400mm and adjust the telescopic terminal. 7. Measure and mark the length on the flue, to ensure a square cut mark the flue all the way around and cut to length. L Y 525 300 Esprit - Installation and Servicing
19 FITTING THE WALL MOUNTING PLATE Screw the wall mounting plate to the wall using 3 wall plugs (previously fitted) with the 3 screws provided. Choose one of the 3 sets of slots in left, right and centre bank. Ensuring that at least one of the screws is fitted into a top slot. 20 MOUNTING THE BOILER 1. Ensure the plastic plugs are removed from both the CH and DHW connections before mounting the boiler. 2. Lift the boiler onto the wall mounting plate (refer to the Introduction section for safe handling advice), locating it over the top angled return. Esprit - Installation and Servicing INSTALLATION esp8817 Example of fixing esp8828 21 FLUE OUTLET
Page 1 and 2: installation and servicing PAKAGED
Page 3 and 4: Esprit - Installation and Servicing
Page 5 and 6: Esprit Natural Gas only Boiler size
Page 7 and 8: SAFETY Current Gas Safety (installa
Page 9 and 10: 1 BOILER WATER CIRCUIT DIAGRAMS CEN
Page 11 and 12: BOILER CONTROL INTERLOCKS Ideal Ste
Page 13 and 14: 6 WATER TREATMENT CENTRAL HEATING T
Page 15 and 16: 8 BOILER ASSEMBLY - Exploded View 2
Page 19: 13 PREPARING THE WALL IMPORTANT. En
Page 27 and 28: 28 FLUE ARRANGEMENT Note. The equiv
Page 29 and 30: esp8826 Inlet Pressure Test Point E
Page 33 and 34: 36 PICTORIAL WIRING DIAGRAM Mains S
Page 35 and 36: 39 INITIAL LIGHTING LEGEND A. Boile
Page 37 and 38: 42 GENERAL CHECKS - continued CENTR
Page 39 and 40: 44 SERVICING SCHEDULE Esprit - Inst
Page 41 and 42: 50 CLEANING THE HEAT EXCHANGER 1. R
Page 43 and 44: 55 BURNER INJECTOR REPLACEMENT 1. R
Page 45 and 46: 3 Esprit - Installation and Servici
Page 49 and 50: 66 PRIMARY PCB REPLACEMENT 1. Refer
Page 51 and 52: 70 SAFETY RELIEF VALVE REPLACEMENT
Page 53 and 54: 74 DHW FLOW SWITCH REPLACEMENT 1. R
Page 55 and 56: 79 PUMP HEAD REPLACEMENT 1. Refer t
Page 57 and 58: 81 EXPANSION VESSEL CHARGING Esprit
Page 59 and 60: 84 FAULT FINDING CHART MAIN MENU FA
Page 61 and 62: 87 L.....A..... (OVERHEAT ERROR) Ca
Page 63 and 64: 93 H.....4.... (DRY FIRE THERMISTOR
Page 65 and 66: 96 SHORT LIST 2 1 32 20 40 esp9182
Page 69: INSTALLER NOTIFICATION GUIDELINES I

iDEAl EsPRit - Ideal Heating

Create successful ePaper yourself

Delete template?

Save as template?