SB-10 USER'S MANUAL

More documents

Recommendations

Info

w SET HORIZONTAL TAB POSITIONS With this command, you cancel all previously set horizontal tabs, and set new positions at lines "nl ”,"n2", etc. There are255 available tab positions. Use 0 to terminate this command. Each horizontal tab must be between 1 and 255, and must be specified in ascending order. CODE: < ESC > D "n" "n2" 0 HEX: 19 44 "nl" "n2" ,.. 00 DECIMAL: 27 68 "nl" "n2" . 0 BASIC: CHR$(27) CHR$(68) CHR$(nl) CHR$(n2) CHW(O) REFERENCE: < ESC > b "n", < HT >, Section 5. w ADVANCE TO NEXT HORIZONTAL TAB This command moves the print head to the next available horizontal tab position. Horizontal tabs are set at power-on to positions 9, 17, 25, 33, etc., to the maximum print position. CODE: HEX: 09 DECIMAL: 9 BASIC: CHRS(9) REFERENCE: D “nl” "n2" ,., 0, Section 5.
I SKIP HORIZONTAL TAB POSITIONS Causes the print head to advance "n" print positions to the right. It does not, however, change the current values of the horizontal tabs. You may choose any number for “n" between 1 and 255. CODE: b "n" HEX: 19 62 "n" -- DECIMAL: 2798 “n" - BASIC: CHR$(27) CHR$(98) CHR$(n) - REFERENCE: D "r-t"n2" ...O. - • MOVE THE PRINT HEAD BACK ONE POSITION (BACKSPACE) Shifts the print head one column to the left. This command can be used to overstrike characters. - CODE: CBS> HEX: 08 DECIMAL: 8 BASIC: CHRS(8) REFERENCE: Section 2. - - 84
Page 1 and 2: - \ - - - - - - - - -
Page 3 and 4: FONT STYLES AND PRINT CONTROLS -
Page 5 and 6: • CANCEL PROPORTIONAL SPAClNG Thi
Page 7 and 8: w SELECT EXPANDED PRINT This instru
Page 9 and 10: • SELECT EMPHASIZED PRINTING This
Page 11 and 12: • CANCEL SUPERSCRIPTS AND SUBSCRI
Page 13 and 14: • REVERSE THE PAPER ONE LINE (REV
Page 15 and 16: • ;yHNGE THE LINE SPACING TO nI60
Page 17 and 18: • ADVANCE PAPER TO TOP OF NEXT PA
Page 19 and 20: • SET THE BOTTOM MARGlN With this
Page 21 and 22: • ADVANCE THE PAPER “n” LINES
Page 23: • SET THE LEFT MARGIN You can use
Page 27 and 28: • PRINT 24-BIT GRAPHICS - With th
Page 29 and 30: Table A-l. Options for the master p
Page 31 and 32: • scELLTHE VALUE OF THE 8TH DATA
Page 33 and 34: • DISABLE THE PRINTER BELL This c
Page 35 and 36: • SELECT INCREMENTAL MODE This co
Page 37 and 38: Printer Installation Menu contains
Page 39 and 40: • USER FUNCTIONS Once you have en
Page 41 and 42: MEMO -- -.
Page 43 and 44: STANDARD ASCII CODES DECIMAL HEXADE
Page 45 and 46: STANDARD ASCII CODES DECIMAL HEXADE
Page 47 and 48: - STANDARD ASCII CODES DECIMAL HEXA
Page 49 and 50: MEMO - - - 108
Page 51 and 52: 2-l Selection of 2-2 international
Page 53 and 54: Decimal Character 54 6 6 91 55 7 7
Page 55 and 56: Decimal Character 208 1. 209 i 270
Page 57 and 58: Graphics Data : i I ] 7.bit Interfa
Page 59 and 60: • PRINTING 8-61-r GRAPHICS In 8-b
Page 61 and 62: 70 NEXT J 80 FOR J==6 TO 0 STEP -1
Page 63 and 64: 140 DATA 1,,2,4,12,8,16,16,48,32 15
Page 65 and 66: A! LINE 70 LINE 80 LINE 90 Prints t
Page 67 and 68: Character matrix 24 dot x 13 dot st
Page 69 and 70: • SERIAL INTERFACE(OPTIONAL) Inte
Page 71 and 72: ACK I I I ;-$-_I DATA ; 9p5ec. Appr
Page 73 and 74: • THE SERIAL INTERFACE(OPTlONAL)
Page 75 and 76:
Serial busy protocols In these prot
Page 77 and 78:
Table H-3. Connector signals for th
Page 79 and 80:
• Hexadecimal codes18 Horizontal
Page 81 and 82:
Federal Communications Commission R
Page 83 and 84:
shipping costs incurred in presenti
Page 85 and 86:
COMMAND QUICK REFERENCE Print Sty/e
Page 87:
! c L / I Graphics Controls yun,u
show all

SB-10 USER'S MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?