SB-10 USER'S MANUAL

More documents

Recommendations

Info

APPENDIX FUNCTION CODE REFERENCE Appendix A contains an entire listing of the codes used for every function performed by your printer. Many of these codes appear throughout the manual, but there are a number of additional functions that are described only in this appendix. So if you’d like to learn about all the capabilities of your printer, you can find them here. Each function is listed by name, followed by a short description. Since there are several different ways to access a function-through escape, control, decimal, and hexadecimal codes, and also through BASIC character strings-we have listed each of your possible choices. The codes are also cross-referenced to other related codes, and to the proper section of the manual. Here are a few tips on using the codes listed in Appendix A: This symbol represents the escape function; for instructions on enabling this function, please consult your computer manual or software manual. n or “n” The “n” appears in the codes for user-selectable functions, such as horizontal tab settings. When you see “n”, you may substitute a number or value within the parameters given in the function’s description. CHR$ The character string command, CHR$, is used to “capture” a code entered when you are programming in BASIC. For details, please see Section 6. Always be sure to enter the code exactly as it appears in the listing. (If a letter is shown in uppercase, enter it in its uppercase form, and vice-versa.)
FONT STYLES AND PRINT CONTROLS - • ;z$ECT THE DRAFT-QUALITY (DQ) CHARACTER This code switches the printer to the draft-quality character set. You can also access the DQ set by turning DIP switch 1-5 on. CODE: 5 HEX: 1B 35 DECIMAL: 27 53 BASIC: CHR$(27) CHR$(53) REFERENCE: < ESC > 4, Section 4 - • ;E+ECT THE LETTER-QUALITY (LQ) CHARACTER This command switches the printer to the LQ character set. (You may also set LQ as the power-on default by turning DIP switch 1-5 off. See Appendix D.) CODE: 4 HEX 1B34 DECIMAL: 27 52 BASIC: CHR$(27) CHR$(52) REFERENCE: < ESC > 5, Section 4. 62
Page 1: - \ - - - - - - - - -
Page 5 and 6: • CANCEL PROPORTIONAL SPAClNG Thi
Page 7 and 8: w SELECT EXPANDED PRINT This instru
Page 9 and 10: • SELECT EMPHASIZED PRINTING This
Page 11 and 12: • CANCEL SUPERSCRIPTS AND SUBSCRI
Page 13 and 14: • REVERSE THE PAPER ONE LINE (REV
Page 15 and 16: • ;yHNGE THE LINE SPACING TO nI60
Page 17 and 18: • ADVANCE PAPER TO TOP OF NEXT PA
Page 19 and 20: • SET THE BOTTOM MARGlN With this
Page 21 and 22: • ADVANCE THE PAPER “n” LINES
Page 23 and 24: • SET THE LEFT MARGIN You can use
Page 25 and 26: I SKIP HORIZONTAL TAB POSITIONS Cau
Page 27 and 28: • PRINT 24-BIT GRAPHICS - With th
Page 29 and 30: Table A-l. Options for the master p
Page 31 and 32: • scELLTHE VALUE OF THE 8TH DATA
Page 33 and 34: • DISABLE THE PRINTER BELL This c
Page 35 and 36: • SELECT INCREMENTAL MODE This co
Page 37 and 38: Printer Installation Menu contains
Page 39 and 40: • USER FUNCTIONS Once you have en
Page 41 and 42: MEMO -- -.
Page 43 and 44: STANDARD ASCII CODES DECIMAL HEXADE
Page 45 and 46: STANDARD ASCII CODES DECIMAL HEXADE
Page 47 and 48: - STANDARD ASCII CODES DECIMAL HEXA
Page 49 and 50: MEMO - - - 108
Page 51 and 52: 2-l Selection of 2-2 international
Page 53 and 54:
Decimal Character 54 6 6 91 55 7 7
Page 55 and 56:
Decimal Character 208 1. 209 i 270
Page 57 and 58:
Graphics Data : i I ] 7.bit Interfa
Page 59 and 60:
• PRINTING 8-61-r GRAPHICS In 8-b
Page 61 and 62:
70 NEXT J 80 FOR J==6 TO 0 STEP -1
Page 63 and 64:
140 DATA 1,,2,4,12,8,16,16,48,32 15
Page 65 and 66:
A! LINE 70 LINE 80 LINE 90 Prints t
Page 67 and 68:
Character matrix 24 dot x 13 dot st
Page 69 and 70:
• SERIAL INTERFACE(OPTIONAL) Inte
Page 71 and 72:
ACK I I I ;-$-_I DATA ; 9p5ec. Appr
Page 73 and 74:
• THE SERIAL INTERFACE(OPTlONAL)
Page 75 and 76:
Serial busy protocols In these prot
Page 77 and 78:
Table H-3. Connector signals for th
Page 79 and 80:
• Hexadecimal codes18 Horizontal
Page 81 and 82:
Federal Communications Commission R
Page 83 and 84:
shipping costs incurred in presenti
Page 85 and 86:
COMMAND QUICK REFERENCE Print Sty/e
Page 87:
! c L / I Graphics Controls yun,u
show all

SB-10 USER'S MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?