SB-10 USER'S MANUAL

More documents

Recommendations

Info

Signal Name Circuit Example 74LS Compatible 3ks-h I3<strong>10</strong>1 -DlOB (To Printer) - 6.2 ki-h T 7438 Compatible NRFD (From Printer) ’ 6.2 k& 5 74LS14 Compatible DAV (To Printer) o 0 7438 Compatible NDAC (From Printer) o 0 6.2 kfs Figure H-5. Circuit example of the IEEE-488 parallel interface. 135
Table H-3. Connector signals for the IEEE-488 interface. PIN SIGNAL NAME DIRECTION FUNCTION 1 DIO 1 IN These signals represent 2 DIO 2 IN parallel data bits 1-4. 3 DIO 3 IN Each signal is at a low 4 DIO 4 IN level for a logical 1, and at a high level for logical 0. 5 N/C Unused. 6 Data Valid IN Indicates valid data. (DA’4 7 Not Ready For OUT Indicates the completion Data (NRFD) of preparation for data reception. 6 Not Data OUT Indicates the completion Accepted (NDAC) of data reception. 9 Interface IN Initializes the Clear (IFC) interface. <strong>10</strong> N/C Unused. 11 Attention (ATN) IN Indicates that d&a on the data bus is either an address or a command. 12 SHIELD Shield. These signals represent 13 DIO 5 IN parallel data bits 5-8. 14 DIO 6 IN Each signal is at a low 15 DIO 7 IN Level for a logical 1, and 16 DIO 8 IN a high level for a logical 0. 17 Remote Enable IN Specifies remote/local. (REV 18-23 GND Ground. 24 LOGIC GND Logic ground. -. - - *********** 136
Page 1 and 2:
- \ - - - - - - - - -
Page 3 and 4:
FONT STYLES AND PRINT CONTROLS -
Page 5 and 6:
• CANCEL PROPORTIONAL SPAClNG Thi
Page 7 and 8:
w SELECT EXPANDED PRINT This instru
Page 9 and 10:
• SELECT EMPHASIZED PRINTING This
Page 11 and 12:
• CANCEL SUPERSCRIPTS AND SUBSCRI
Page 13 and 14:
• REVERSE THE PAPER ONE LINE (REV
Page 15 and 16:
• ;yHNGE THE LINE SPACING TO nI60
Page 17 and 18:
• ADVANCE PAPER TO TOP OF NEXT PA
Page 19 and 20:
• SET THE BOTTOM MARGlN With this
Page 21 and 22:
• ADVANCE THE PAPER “n” LINES
Page 23 and 24:
• SET THE LEFT MARGIN You can use
Page 25 and 26: I SKIP HORIZONTAL TAB POSITIONS Cau
Page 27 and 28: • PRINT 24-BIT GRAPHICS - With th
Page 29 and 30: Table A-l. Options for the master p
Page 31 and 32: • scELLTHE VALUE OF THE 8TH DATA
Page 33 and 34: • DISABLE THE PRINTER BELL This c
Page 35 and 36: • SELECT INCREMENTAL MODE This co
Page 37 and 38: Printer Installation Menu contains
Page 39 and 40: • USER FUNCTIONS Once you have en
Page 41 and 42: MEMO -- -.
Page 43 and 44: STANDARD ASCII CODES DECIMAL HEXADE
Page 45 and 46: STANDARD ASCII CODES DECIMAL HEXADE
Page 47 and 48: - STANDARD ASCII CODES DECIMAL HEXA
Page 49 and 50: MEMO - - - 108
Page 51 and 52: 2-l Selection of 2-2 international
Page 53 and 54: Decimal Character 54 6 6 91 55 7 7
Page 55 and 56: Decimal Character 208 1. 209 i 270
Page 57 and 58: Graphics Data : i I ] 7.bit Interfa
Page 59 and 60: • PRINTING 8-61-r GRAPHICS In 8-b
Page 61 and 62: 70 NEXT J 80 FOR J==6 TO 0 STEP -1
Page 63 and 64: 140 DATA 1,,2,4,12,8,16,16,48,32 15
Page 65 and 66: A! LINE 70 LINE 80 LINE 90 Prints t
Page 67 and 68: Character matrix 24 dot x 13 dot st
Page 69 and 70: • SERIAL INTERFACE(OPTIONAL) Inte
Page 71 and 72: ACK I I I ;-$-_I DATA ; 9p5ec. Appr
Page 73 and 74: • THE SERIAL INTERFACE(OPTlONAL)
Page 75: Serial busy protocols In these prot
Page 79 and 80: • Hexadecimal codes18 Horizontal
Page 81 and 82: Federal Communications Commission R
Page 83 and 84: shipping costs incurred in presenti
Page 85 and 86: COMMAND QUICK REFERENCE Print Sty/e
Page 87: ! c L / I Graphics Controls yun,u
show all

SB-10 USER'S MANUAL

Create successful ePaper yourself

Delete template?

Save as template?