SB-10 USER'S MANUAL

More documents

Recommendations

Info

• SELECT AN INTERNATIONAL CHARACTER SET This command selects one of eight international character sets determined by thevalue of “n”, as shown below. (You can also select a particular International Character Set as a power-on default. To do this, please turn to Appendix D, “DIP Switches.“) CODE: R “n” HEX: DECIMAL: BASIC: IB 52 “n” 27 82 “n” CHRS(27) CHR$(82) CHR$(n) USA=0 France=1 Germany=2 England=3 Denmark=4 Sweden = 5 Italy = 6 Spain = 7 • SET THE PROPORTIONAL SPACING In the letter-quality mode, this command causes all subsequent printing to be done in proportional spacing. CODE: P 1 HEX: iB 70 01 DECIMAL: 27 112 1 BASIC: REFERENCE: CHR$(27) CHR$(112) CHR$(l) < ESC > P 0, Section4 63
• CANCEL PROPORTIONAL SPAClNG This command cancels the proportional spacing and returns the print pitch to pica. CODE: PO HEX: 1B 70 00 DECIMAL: 27 1120 BASIC: CHR$(27) CHR$(ll2) CHR$(O) REFERENCE: < ESC > p 1, Section4 • SET THE PRINT PITCH TO PICA (IO CPI) In the draft mode, this command causes all subsequent printing to be done in pica type. This command also sets the maximum line length to 80 characters. You can select pica type as the power-on default by turning on DIP switch l-6. CODE: P HEX: 1B 50 DECIMAL: 27 80 1 - - BASIC: CHW(27) CHR$(80) REFERENCE: < ESC > M, Section 4. 64
Page 1 and 2: - \ - - - - - - - - -
Page 3: FONT STYLES AND PRINT CONTROLS -
Page 7 and 8: w SELECT EXPANDED PRINT This instru
Page 9 and 10: • SELECT EMPHASIZED PRINTING This
Page 11 and 12: • CANCEL SUPERSCRIPTS AND SUBSCRI
Page 13 and 14: • REVERSE THE PAPER ONE LINE (REV
Page 15 and 16: • ;yHNGE THE LINE SPACING TO nI60
Page 17 and 18: • ADVANCE PAPER TO TOP OF NEXT PA
Page 19 and 20: • SET THE BOTTOM MARGlN With this
Page 21 and 22: • ADVANCE THE PAPER “n” LINES
Page 23 and 24: • SET THE LEFT MARGIN You can use
Page 25 and 26: I SKIP HORIZONTAL TAB POSITIONS Cau
Page 27 and 28: • PRINT 24-BIT GRAPHICS - With th
Page 29 and 30: Table A-l. Options for the master p
Page 31 and 32: • scELLTHE VALUE OF THE 8TH DATA
Page 33 and 34: • DISABLE THE PRINTER BELL This c
Page 35 and 36: • SELECT INCREMENTAL MODE This co
Page 37 and 38: Printer Installation Menu contains
Page 39 and 40: • USER FUNCTIONS Once you have en
Page 41 and 42: MEMO -- -.
Page 43 and 44: STANDARD ASCII CODES DECIMAL HEXADE
Page 45 and 46: STANDARD ASCII CODES DECIMAL HEXADE
Page 47 and 48: - STANDARD ASCII CODES DECIMAL HEXA
Page 49 and 50: MEMO - - - 108
Page 51 and 52: 2-l Selection of 2-2 international
Page 53 and 54: Decimal Character 54 6 6 91 55 7 7
Page 55 and 56:
Decimal Character 208 1. 209 i 270
Page 57 and 58:
Graphics Data : i I ] 7.bit Interfa
Page 59 and 60:
• PRINTING 8-61-r GRAPHICS In 8-b
Page 61 and 62:
70 NEXT J 80 FOR J==6 TO 0 STEP -1
Page 63 and 64:
140 DATA 1,,2,4,12,8,16,16,48,32 15
Page 65 and 66:
A! LINE 70 LINE 80 LINE 90 Prints t
Page 67 and 68:
Character matrix 24 dot x 13 dot st
Page 69 and 70:
• SERIAL INTERFACE(OPTIONAL) Inte
Page 71 and 72:
ACK I I I ;-$-_I DATA ; 9p5ec. Appr
Page 73 and 74:
• THE SERIAL INTERFACE(OPTlONAL)
Page 75 and 76:
Serial busy protocols In these prot
Page 77 and 78:
Table H-3. Connector signals for th
Page 79 and 80:
• Hexadecimal codes18 Horizontal
Page 81 and 82:
Federal Communications Commission R
Page 83 and 84:
shipping costs incurred in presenti
Page 85 and 86:
COMMAND QUICK REFERENCE Print Sty/e
Page 87:
! c L / I Graphics Controls yun,u
show all

SB-10 USER'S MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?