Hardware Interface Description - KORE Telematics

More documents

Recommendations

Info

XT55/56 Hardware Interface Description Confidential / Released s 8 Reference approval 8.1 Reference equipment for type approval The Siemens reference setup submitted to type approve XT55/56 consists of the following components: • Siemens XT55/56 cellular engine • Development Support Box (DSB45) • Flex cable (160 mm) from Hirose DF12C receptacle on XT55/56 to Hirose DF12 connector on DSB45. Please note that this cable is not included in the scope of delivery of DSB45. • SIM card reader integrated on DSB45 • Handset type Votronic HH-SI-30.3/V1.1/0 • PC as MMI Antenna or 50 Ω cable to system simulator Antenna cable Active GPS antenna PC RS-232 DSB45 Flex cable 160mm GSM engine GPS engine GP DAI cable for acoustic measuring SIM Power supply DAI Box Handset Acoustic tester Figure 55: Reference equipment for approval XT55/56_hd_v02.06a Page 116 of 125 17.12.2004
XT55/56 Hardware Interface Description Confidential / Released s 8.2 Compliance with FCC Rules and Regulations (XT55 only) The FCC Equipment Authorization Certification for the XT55 reference application described in Chapter 8.1 is listed under the FCC identifier QIPXT55 IC: 267W-XT55 granted to Siemens AG. The XT55 reference application registered under the above identifier is certified to be in accordance with the following Rules and Regulations of the Federal Communications Commission (FCC). “This device contains GSM 900MHz and GSM 1800MHz functions that are not operational in U.S. Territories. This device is to be used only for mobile and fixed applications. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Antennas used for this OEM module must not exceed 7dBi gain for mobile and fixed operating configurations. This device is approved as a module to be installed in other devices. Each OEM must obtain their own Certification for each device containing this module.” IMPORTANT: Manufacturers of mobile or fixed devices incorporating XT55 modules are advised to • clarify any regulatory questions, • have their completed product tested, • have product approved for FCC compliance, and • include instructions according to above mentioned RF exposure statements in end product user manual. XT55/56_hd_v02.06a Page 117 of 125 17.12.2004
Page 1 and 2:
XT55/56 Hardware Interface Descript
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66: XT55/56 Hardware Interface Descript
Page 115: XT55/56 Hardware Interface Descript
Page 125: XT55/56 Hardware Interface Descript
show all

Hardware Interface Description - KORE Telematics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?