Ultralow power ARM-based 32-bit MCU with 384 Kbytes Flash ... - Keil

More documents

Recommendations

Info

Electrical characteristicsSTM32L162VD, STM32L162ZD, STM32L162QD, STM32L162RD6.2 Absolute maximum ratingsStresses above the absolute maximum ratings listed in Table 7: Voltage characteristics,Table 8: Current characteristics, and Table 9: Thermal characteristics may cause permanentdamage to the device. These are stress ratings only and functional operation of the deviceat these conditions is not implied. Exposure to maximum rating conditions for extendedperiods may affect device reliability.Table 7.Voltage characteristicsSymbol Ratings Min Max UnitV DD –V SSV IN(2)External main supply voltage(including V DDA and V DD ) (1)–0.3 4.0Input voltage on five-volt tolerant pin V SS −0.3 V DD +4.0Input voltage on any other pin V SS −0.3 4.0|ΔV DDx | Variations between different V DD power pins 50|V SSX −V SS | Variations between all different ground pins 50V ESD(HBM)Electrostatic discharge voltage(human body model)see Section 6.3.11VmV1. All main power (V DD , V DDA ) and ground (V SS , V SSA ) pins must always be connected to the external powersupply, in the permitted range.2. V IN maximum must always be respected. Refer to Table 8 for maximum allowed injected current values.Table 8.Current characteristicsSymbol Ratings Max. UnitI VDD Total current into V DD /V DDA power lines (source) (1)I VSS Total current out of V SS ground lines (sink) (1) 80I IOOutput current sourced by any I/O and control pin - 25Output current sunk by any I/O and control pin 25(2)I INJ(PIN)Injected current on five-volt tolerant I/O (3)+0 /-5Injected current on any other pin (4)± 5ΣI INJ(PIN) Total injected current (sum of all I/O and control pins) (5) ± 251. All main power (V DD , V DDA ) and ground (V SS , V SSA ) pins must always be connected to the external powersupply, in the permitted range.2. Negative injection disturbs the analog performance of the device. See note in Section 6.3.17.3. Positive current injection is not possible on these I/Os. A negative injection is induced by V IN V DD while a negative injection is induced by V IN < V SS . I INJ(PIN)must never be exceeded. Refer to Table 7: Voltage characteristics for the maximum allowed input voltagevalues.5. When several inputs are submitted to a current injection, the maximum ΣI INJ(PIN) is the absolute sum of thepositive and negative injected currents (instantaneous values).80mA50/124 Doc ID 022268 Rev 2
STM32L162VD, STM32L162ZD, STM32L162QD, STM32L162RDElectrical characteristicsTable 9. Thermal characteristicsSymbol Ratings Value UnitT STG Storage temperature range –65 to +150 °CT J Maximum junction temperature 150 °C6.3 Operating conditions6.3.1 General operating conditionsTable 10.General operating conditionsSymbol Parameter Conditions Min Max Unitf HCLK Internal AHB clock frequency 0 32f PCLK1 Internal APB1 clock frequency 0 32f PCLK2 Internal APB2 clock frequency 0 32V DDV DDA(1)P DTAStandard operating voltageAnalog operating voltage(ADC and DAC not used)Analog operating voltage(ADC or DAC used)Power dissipation atT A = 85 °C (3)Temperature range1. When the ADC is used, refer to Table 59: ADC characteristics.BOR detector disabled 1.65 3.6BOR detector enabled,at power onBOR detector disabled,after power onMust be the same voltageas V DD(2)1.8 3.61.65 3.61.65 3.61.8 3.6Maximum power dissipation –40 85Low power dissipation (4)–40 1052. It is recommended to power V DD and V DDA from the same source. A maximum difference of 300 mVbetween V DD and V DDA can be tolerated during power-up and operation.3. If T A is lower, higher P D values are allowed as long as T J does not exceed T J max (see Table 73: Thermalcharacteristics on page 121).MHzVV290 mWTJ Junction temperature range -40 °C ≤T A ≤105 °C –40 105 °C4. In low power dissipation state, T A can be extended to this range as long as T J does not exceed T J max(see Table 73: Thermal characteristics on page 121).°CDoc ID 022268 Rev 2 51/124
Page 1 and 2: STM32L162VD STM32L162ZDSTM32L162QD
Page 3 and 4: STM32L162VD, STM32L162ZD, STM32L162
Page 6: List of tablesSTM32L162VD, STM32L16
Page 24 and 25: Functional overviewSTM32L162VD, STM
Page 26 and 27: Functional overviewSTM32L162VD, STM
Page 28 and 29: Pin descriptionsSTM32L162VD, STM32L
Page 38 and 39: 38/124 Doc ID 022268 Rev 2Table 6.P
Page 48 and 49: Electrical characteristicsSTM32L162
Page 100 and 101:
Electrical characteristicsSTM32L162
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Package characteristicsSTM32L162VD,
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Ordering information schemeSTM32L16
Page 124:
STM32L162VD, STM32L162ZD, STM32L162
show all

Ultralow power ARM-based 32-bit MCU with 384 Kbytes Flash ... - Keil

Create successful ePaper yourself

Delete template?

Save as template?