Ultralow power ARM-based 32-bit MCU with 384 Kbytes Flash ... - Keil

More documents

Recommendations

Info

Electrical characteristicsSTM32L162VD, STM32L162ZD, STM32L162QD, STM32L162RDWakeup time from low-power modeThe wakeup times given in the following table are measured with the MSI RC oscillator. Theclock source used to wake up the device depends on the current operating mode:● Sleep mode: the clock source is the clock that was set before entering Sleep mode● Stop mode: the clock source is the MSI oscillator in the range configured beforeentering Stop mode● Standby mode: the clock source is the MSI oscillator running at 2.1 MHzAll timings are derived from tests performed under ambient temperature and V DD supplyvoltage conditions summarized in Table 10.Table 21.Typical and maximum timings in Low power modesSymbol Parameter Conditions Typ Max (1)Unitt WUSLEEP Wakeup from Sleep mode f HCLK = 32 MHz 0.4t WUSLEEP_LPt WUSTOPt WUSTDBYWakeup from Low powersleep modef HCLK = 262 kHzWakeup from Stop mode,regulator in Run modef HCLK = 262 kHzFlash enabledf HCLK = 262 kHzFlash switched OFFf HCLK = f MSI = 4.2 MHzf HCLK = f MSI = 4.2 MHzVoltage range 1 and 2f HCLK = f MSI = 4.2 MHzVoltage range 34646TBD7.7 8.98.2 13.1f HCLK = f MSI = 2.1 MHz 10.2 13.4Wakeup from Stop mode,regulator in low power mode f HCLK = f MSI = 1.05 MHz 16 20f HCLK = f MSI = 524 kHz 31 37f HCLK = f MSI = 262 kHz 57 66f HCLK = f MSI = 131 kHz 112 123f HCLK = MSI = 65 kHz 221 236Wakeup from Standby modefFWU bit = 1HCLK = MSI = 2.1 MHz 58 104Wakeup from Standby modefFWU bit = 0HCLK = MSI = 2.1 MHz 2.6 3.25 msµs1. Based on characterization, not tested in production, unless otherwise specified62/124 Doc ID 022268 Rev 2
STM32L162VD, STM32L162ZD, STM32L162QD, STM32L162RDElectrical characteristicsOn-chip peripheral current consumptionThe current consumption of the on-chip peripherals is given in the following table. The MCUis placed under the following conditions:● all I/O pins are in input mode with a static value at V DD or V SS (no load)● all peripherals are disabled unless otherwise mentioned● the given value is calculated by measuring the current consumption– with all peripherals clocked off– with only one peripheral clocked onTable 22. Peripheral current consumption (1)Typical consumption, V DD = 3.0 V, T A = 25 °CPeripheralRange 1,V CORE =1.8 VVOS[1:0] =01Range 2,V CORE =1.5 VVOS[1:0] =10Range 3,V CORE =1.2 VVOS[1:0] =11Low powersleep andrunUnitAPB1TIM2 TBD TBD TBD TBDTIM3 TBD TBD TBD TBDTIM4 TBD TBD TBD TBDTIM6 TBD TBD TBD TBDTIM7 TBD TBD TBD TBDLCD TBD TBD TBD TBDWWDG TBD TBD TBD TBDSPI2 TBD TBD TBD TBDUSART2 TBD TBD TBD TBDUSART3 TBD TBD TBD TBDI2C1 TBD TBD TBD TBDI2C2 TBD TBD TBD TBDUSB TBD TBD TBD TBDPWR TBD TBD TBD TBDDAC TBD TBD TBD TBDCOMP TBD TBD TBD TBDµA/MHz(f HCLK )Doc ID 022268 Rev 2 63/124
Page 1 and 2:
STM32L162VD STM32L162ZDSTM32L162QD
Page 3 and 4:
STM32L162VD, STM32L162ZD, STM32L162
Page 6:
List of tablesSTM32L162VD, STM32L16
Page 9 and 10:
Page 11 and 12: STM32L162VD, STM32L162ZD, STM32L162
Page 24 and 25: Functional overviewSTM32L162VD, STM
Page 26 and 27: Functional overviewSTM32L162VD, STM
Page 28 and 29: Pin descriptionsSTM32L162VD, STM32L
Page 38 and 39: 38/124 Doc ID 022268 Rev 2Table 6.P
Page 48 and 49: Electrical characteristicsSTM32L162
Page 112 and 113:
Electrical characteristicsSTM32L162
Page 114 and 115:
Package characteristicsSTM32L162VD,
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Ordering information schemeSTM32L16
Page 124:
show all

Ultralow power ARM-based 32-bit MCU with 384 Kbytes Flash ... - Keil

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?