EMIS Interface Description - Measurement Solutions

More documents

Recommendations

Info

Specification Euro Interface EMIS Interface Description If printer is assigned to OBC: Direction Telegram EMIS SET,PRN,TEXT=“Lieferschein\r\n“ OBC OBC OBC ... ... EMIS SET,PRN,STATUS,MODE=“READY“ Sening® Innovative Tank Truck Systems OBC After discharge the measuring system(s) access the printer for printing the original receipt. The printer access is requested from EMIS. For this reason the OBC must release the printer after printing the header by sending SET,PRN,STATUS,MODE=“READY“ wieder freigibt. 10 - Check if all discharges are finished The measuring results can be found in the METER,ORDERS,RESULT(n) area. For a clear assignment the order corresponds to the presets, i.e. RESULT(0) contains the measuring results which correspond to PRESET(0), RESULT(1) corresponds to PRESET(1) etc. Direction Telegram EMIS REQUEST,METER,ORDERS,RESULT(0),Check OBC OBC REPORT,METER,ORDERS,RESULT(0),CHECK=““ EMIS The result is not yet available. The procedure shown above must be performed for all expected results. Reasons: The discharge is not finished (in case of MultiFlow measuring systems, the actual mode can be determined by command REQUEST,METER(n),STATUS,MODE . If EMIS reports MODE=“BUSY“, the discharge is in progress) or the measuring system was not able to discharge the corresponding product (e.g. the system is not configured for this product). It must be considered that the job distribution can not be determined If several measuring systems are connected. � OBC must continue waiting for the result(s), interruption by the operator must be provided (if necessary) Direction Telegram EMIS REQUEST,METER,ORDERS,RESULT(0),Check OBC OBC REPORT,METER,ORDERS,RESULT(0),CHECK=“OK“ EMIS The result is available. The procedure shown above must be performed for all expected results. � Proceed with the program. 64 Rev. 2.00 / MB / jp / Juli 2008 MNF19002EUS / DOK-411E
Sening® Innovative Tank Truck Systems 11 - Collect delivery results Direction Telegram Specification Euro Interface EMIS Interface Description EMIS REQUEST,METER,ORDERS,RESULT(0) OBC OBC REPORT,METER,ORDERS,RESULT(0),PCODE="001";VOLUME=" 10020"; PUNIT="L";METERID="- ? - ";RECEIPTID="0000000017";MODEID="15"; AVTEMP="+50,4";TUNIT="_C";DATE="28.11.00";STARTTIME="10:02"; ENDTIME="10:14";VT="010330,00";VC="010020,00";MASS="008480,00"; CHECK="OK" EMIS The procedure shown above must be performed for all expected results. � Proceed with the program. 12 - Printing further data by OBC After transmission of the results the OBC may print further information, e.g. delivery note, invoice, etc. The procedure is equal to the example shown in step 9 (print header). MNF19002EUS / DOK-411E Rev. 2.00 / MB / jp / Juli 2008 65 1 2 3 4 5 6 7 8 9 A Programming Details
Page 1 and 2:
Specification Euro Interface EMIS I
Page 3 and 4:
Sening® Innovative Tank Truck Syst
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14: Sening® Innovative Tank Truck Syst
Page 63: Sening® Innovative Tank Truck Syst
Page 73 and 74: Sening ® Innovative Tank Truck Sys
Page 94: The specifications contained herein
show all

EMIS Interface Description - Measurement Solutions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?