Renamic - BIOTRONIK USA - News

More documents

Recommendations

Info

36 Using RenamicPrintingFigure 12: Printer buttonsThe printer buttons are located on the left front side of theRenamic, as shown in Figure 12. For a description of eachbutton and its function, refer to Table 1 on page 27.
37 Using RenamicECG and IEGMFunctionsTakingScreenshotsThe IEGMs received from the implanted device and surfaceECG can be displayed and printed simultaneously. Therecording of the surface ECG is independent of otherfunctions, so the implanted device can be interrogated andprogrammed during the ongoing ECG display. The recordedelectrograms can be saved and measured using calipers.When the ECG is overmodulated, the signal is displayed onlyas a solid line on the upper frame of the ECG window. To fix theovermodulation, test the lead contacts, remove other devicesfrom the patient, and turn off the sources of interference.To take a snapshot of the current screen displayed onRenamic, follow the instructions listed below:1. Make sure that the USB drive on which you wish to storethe image is plugged into one of the available USB ports.See page 23.2. Pull out the printer paper tray as if you were going toreplace the paper. The printer tray must be out in order totake screenshots.3. Press and hold the button.4. While holding the button, press and release the10 button.The screenshot is now saved to the USB stick as a PNG file.
Page 3 and 4: 1Table of ContentsIndications for U
Page 5 and 6: 3 Table of ContentsSupplementary In
Page 7: 5Indications and Contraindications
Page 11: 9 Warnings and Precautionstouching
Page 14 and 15: 12 General Safety InstructionsGener
Page 16 and 17: 14 General Safety InstructionsElect
Page 18 and 19: 16 General Safety InstructionsSensi
Page 20 and 21: 18 Device OverviewDevice OverviewAn
Page 22 and 23: 20 Device OverviewFigure 3: Power c
Page 25 and 26: 23 Start UpECG Port and USB Device
Page 28 and 29: 26 Start UpWhen possible, use the O
Page 30 and 31: 28 Using RenamicEmergencyProgramsRe
Page 32 and 33: 30 Using RenamicTelemetryThe progra
Page 34 and 35: 32 Using RenamicLED Status (flashin
Page 36 and 37: 34 Using RenamicUsing theInternal P
Page 40 and 41: 38 Renamic PSAOverviewRenamic PSATh
Page 42 and 43: 40 Renamic PSAConnecting thepatient
Page 44 and 45: 42 Renamic PSAa. Rate - current rat
Page 46 and 47: 44 Renamic PSAParameter Range Remar
Page 48 and 49: 46 Renamic PSAFigure 17: Saving mea
Page 50 and 51: 48 Renamic PSAFigure 19: Burst paci
Page 52 and 53: 50 Renamic PSAFigure 21: Completed
Page 54 and 55: 52 Renamic PSAFigure 23: Sensing te
Page 56 and 57: 54 Renamic PSAFigure 25: Threshold
Page 58 and 59: 56 Renamic PSAFigure 27: Adjust scr
Page 60: 58 Renamic PSAFigure 28: The Freeze
Page 63 and 64: 61 Renamic PSAFigure 31: ID NumberF
Page 65: 63 Renamic PSAFigure 34: Date of Bi
Page 68 and 69: 66 Renamic PSAHospitaland CityThe h
Page 71 and 72: 69 Renamic PSATypeThe type of lead
Page 73 and 74: 71 Renamic PSAIf a device is interr
Page 75 and 76: 73 MaintenanceMaintenanceTo clean a
Page 77 and 78: 75 SafetyOperatingConditions• Do
Page 79 and 80: 77 Technical DataTechnical DataSee
Page 81 and 82: 79 Technical DataInternal printerCa
Page 83 and 84: 81 Supplementary InformationSupplem
Page 85 and 86: 83 Supplementary InformationUL-cert
Page 88 and 89:
86 Symbols on the ComponentsThe sym
Page 90 and 91:
88 Symbols on the ComponentsLegend
Page 94:
M4147-B 07/13© 2013 BIOTRONIK, Inc
show all

Renamic - BIOTRONIK USA - News

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?