Renamic - BIOTRONIK USA - News

More documents

Recommendations

Info

52 <strong>Renamic</strong> PSAFigure 23: Sensing test for the RV channelImpedanceTo test the impedance, program the desired output andincrease the basic rate to 10-15 beats above the intrinsicrate to ensure pacing. The impedance value is displayed inthe real-time screen in the upper right corner of the screen.Real-time impedance values are displayed in the right uppercorner, as shown in the black box in Figure 24.Select the chamber to record the impedance measurement;an example using the LV channel is shown in the blue box inFigure 24. Press the Impedance button (green box) underthe Save measurement section to save the data to the Reportscreen. A message stating “Values saved” will appear on themessage bar, shown with the red box in Figure 24.
53 <strong>Renamic</strong> PSAFigure 24: Impedance testThresholdTo start the threshold test, first select the chamber beingmeasured under the Save measurement section. An exampleis shown in the blue box in Figure 25. Press the amplitudebutton (black box) for the chamber being tested, in this casethe RV channel. Decrease the output by using the slidebaror – button until capture is lost. Increase the output toregain threshold and press the Threshold button under theSave measurement section to save the data to the Reportscreen. A message stating “Values saved” will appear on themessage bar, as shown with the red box in Figure 25.Increase the output if the patient is pacemaker dependent toregain capture or decrease the rate to end the test.
Page 3 and 4: 1Table of ContentsIndications for U
Page 5 and 6: 3 Table of ContentsSupplementary In
Page 7: 5Indications and Contraindications
Page 11: 9 Warnings and Precautionstouching
Page 14 and 15: 12 General Safety InstructionsGener
Page 16 and 17: 14 General Safety InstructionsElect
Page 18 and 19: 16 General Safety InstructionsSensi
Page 20 and 21: 18 Device OverviewDevice OverviewAn
Page 22 and 23: 20 Device OverviewFigure 3: Power c
Page 25 and 26: 23 Start UpECG Port and USB Device
Page 28 and 29: 26 Start UpWhen possible, use the O
Page 30 and 31: 28 Using RenamicEmergencyProgramsRe
Page 32 and 33: 30 Using RenamicTelemetryThe progra
Page 34 and 35: 32 Using RenamicLED Status (flashin
Page 36 and 37: 34 Using RenamicUsing theInternal P
Page 38 and 39: 36 Using RenamicPrintingFigure 12:
Page 40 and 41: 38 Renamic PSAOverviewRenamic PSATh
Page 42 and 43: 40 Renamic PSAConnecting thepatient
Page 44 and 45: 42 Renamic PSAa. Rate - current rat
Page 46 and 47: 44 Renamic PSAParameter Range Remar
Page 48 and 49: 46 Renamic PSAFigure 17: Saving mea
Page 50 and 51: 48 Renamic PSAFigure 19: Burst paci
Page 52 and 53: 50 Renamic PSAFigure 21: Completed
Page 56 and 57: 54 Renamic PSAFigure 25: Threshold
Page 58 and 59: 56 Renamic PSAFigure 27: Adjust scr
Page 60: 58 Renamic PSAFigure 28: The Freeze
Page 63 and 64: 61 Renamic PSAFigure 31: ID NumberF
Page 65: 63 Renamic PSAFigure 34: Date of Bi
Page 68 and 69: 66 Renamic PSAHospitaland CityThe h
Page 71 and 72: 69 Renamic PSATypeThe type of lead
Page 73 and 74: 71 Renamic PSAIf a device is interr
Page 75 and 76: 73 MaintenanceMaintenanceTo clean a
Page 77 and 78: 75 SafetyOperatingConditions• Do
Page 79 and 80: 77 Technical DataTechnical DataSee
Page 81 and 82: 79 Technical DataInternal printerCa
Page 83 and 84: 81 Supplementary InformationSupplem
Page 85 and 86: 83 Supplementary InformationUL-cert
Page 88 and 89: 86 Symbols on the ComponentsThe sym
Page 90 and 91: 88 Symbols on the ComponentsLegend
Page 94: M4147-B 07/13© 2013 BIOTRONIK, Inc

Renamic - BIOTRONIK USA - News

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?