MicroMaster 6SE92 - ECT Sales & Service

More documents

Recommendations

Info

MICROMASTERMICROMASTER VectorMIDIMASTER VectorMotor Data7. Motor data 7/17.1 Engineering Information 7/17.2 Motor - Drive Converter Assignment 7/37.2.1 Rated Motor Current Greater than the Rated Drive Converter 7/3Current7.2.2 Fan and Pump Drives with 1LA5, 1LA6 and 1LA7 Motors 7/3(“Variable Torque”, VT)7.2.3 Information Regarding the Tables 7/37.2.4 230 V AC Supply Voltage 2 Pole Motor 7/47.2.5 230 V AC Supply Voltage 4 Pole Motor 7/67.2.6 230 V AC Supply Voltage 6 Pole Motors 7/87.2.7 230 V AC Supply Voltage 8 Pole Motors 7/107.2.8 400 V AC Supply Voltage 2 Pole Motors 7/127.2.9 400 V AC Supply Voltage 4 Pole Motors 7/147.2.10 400 V AC Supply Voltage 6 Pole Motors 7/167.2.11 400 V AC Supply Voltage 8 Pole Motors 7/187.2.12 500 V AC Supply Voltage 2 Pole Motors 7/207.2.13 500 V AC Supply Voltage 4 Pole Motors 7/227.2.14 500 V AC Supply Voltage 6 Pole Motors 7/247.2.15 500 V AC Supply Voltage 8 Pole Motors 7/26
MICROMASTERMICROMASTER VectorMIDIMASTER VectorMotor Data7. MOTOR DATA7.1 Engineering InformationA detailed description of the motors is provided in thefollowing catalogues:M 11:DA 47:DA 48:LV motors: Squirrel Cage Induction motorsReluctance motors: Synchronousmotors for variable-speed drivesSIEMOSYN motors: permanentmagnetsynchronous motorsForce-ventilated Motors:In addition to self-ventilated 1LA5 1LA6 and 1LA7 motors,force-ventilated 1LA5/1LA7 motors can also be used.According to Figure 1, the permissible S1-torque can beused, at rated frequency, down to standstill.It is practical to use force-ventilated motors, if high torqueutilisation is required, even at the lowest speeds.Standard motors with pole numbers greater than 4 are to beoperated at speeds > approx. 2200 RPM (e.g. in the fieldweakeningrange). Thus, for self-ventilated motors the fannoise is decreased.The engineering guidelines specified here refer to Siemens1LA5, 1LA6 and 1LA7 induction motors as well as Siemensforce-ventilated 1LA5 motors. If third-party induction motorsare used, their specific engineering data must be observed.All types of load characteristics are possible; only the mostimportant will be discussed here:- Constant-torque DrivesWhen M = const. ("Constant Torque", CT)- Fan and pump driveswith M ~ n² ("Variable Torque", VT).M/Mn%100908070Constant flux rangeFor forced ventilationField-weakening rangeUtilized to temperature rise class FUtilized to temperature rise class BTorque Utilisation of Motors:60The motor best suited for a specific application depends onits permissible torque characteristic over the speed range.10 20 30 40 50 60 70 80f [Hz]The typical characteristics of the permissible continuoustorque for a self-ventilated motor with a 50 Hz rated frequencyare illustrated in Figure 1. As a result of the low cooling effectat low speeds, the torque which can be utilised is significantlylower than at 50 Hz. The torque de-rating factor is not thesame for all motors. The assignment tables from Page 7/6onwards specify the torque de-rating as a function of thespeed in the frequency range of f = 0 Hz to 50 Hz whenutilised to temperature rise class F.For frequencies above rated frequency f n, the voltage remainsconstant when the maximum drive converter output voltagehas been reached. In this range, the motor is operated in fieldweakening. The torque which can be thermally utiliseddecreases with approx. f n/f. As the stall torque decreases with(f n/f) 2 , the safety margin to the stall torque decreases and thedrive load capability is lower.Figure 1: Typical Characteristic Of The PermissibleTorque For Force-Ventilated Motors(e.g. 1LA5/1LA6/1LA7) with 50 Hz RatedFrequency.(Precise values for 1LA5, 1LA6 and 1LA7motors can be taken from the AssignmentTables on Page 7/6 onwards).Maximum Speeds:The maximum mechanical speeds for 1LA5, 1LA6 and 1LA7motors are specified in Catalogue M11.For MICROMASTER and MIDIMASTER drives with a fieldweakeningrange f = 50 Hz to 100 Hz, the output up to 100 Hzdecreases for 1LA5, 1LA6 and 1LA7 motors by approximately10%.The assignment tables indicate that Siemens1LA5/1LA6/1LA7 induction motors, when utilised according totemperature rise class F, in the control range 1:2, cangenerally be operated at 100% rated torque. When utilisedaccording to temperature rise class B, the permissible torquefor 1LA5/1LA6/1LA7 motors must be reduced byapproximately 10%.Siemens DA 64 – 1998/99 (04/99) 7/1
Page 1 and 2:
MICROMASTERMICROMASTER VectorMIDIMA
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: MICROMASTERMICROMASTER VectorMIDIMA
Page 55 and 56: Standard ApplicationsMICROMASTERMIC
Page 67 and 68: Communications/InterfacesMICROMASTE
Page 89 and 90: Inverter Selection and Ordering Dat
Page 101: Inverter Selection and Ordering Dat
Page 131 and 132: COMBIMASTER & MICROMASTER Integrate
Page 153 and 154:
COMBIMASTER & MICROMASTER Integrate
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
AppendixMICROMASTERMICROMASTER Vect
show all

MicroMaster 6SE92 - ECT Sales & Service

Create successful ePaper yourself

Delete template?

Save as template?