MicroMaster 6SE92 - ECT Sales & Service

More documents

Recommendations

Info

MICROMASTERMICROMASTER VectorMIDIMASTER VectorStandard ApplicationsParameter settings for this application which are changed from their defaults:Note that P009 must be set to 2 or 3 before parameter numbers above P009 can be modified.Number Value MeaningP002 3.00 Ramp Up time 3.0 secondsP003 3.00 Ramp Down time 3.0 secondsP006 1 Analogue setpoint controlP007 0 Front panel keys disabledP015 1 Automatic start on power up if run switch is enabledP016 3 Flying Start in forward direction enabledP021 25.00 Minimum analogue setpoint 25%P022 50.00 Maximum analogue setpoint 50%P026 2 Analogue output 2 indicates motor currentP052 10 Din2 used to reset drive faultP062 1 Relay output 2 indicates drive runningP077 2 Quadratic V/F curve selectedP080 0.83 Motor rating plate power factor = 0.83P082 1460 Motor rating plate speed = 1460 RPMP083 21.9 Motor rating plate current = 21.9 AP201 1 PID closed loop control enabledP202 0.2 Proportional Gain coefficient 0.2P203 0.05 Integral Gain coefficient 0.05P207 10 Integral error is cleared if the error between setpoint and feedback>10%P211 25.00 0 setpoint corresponds to 25%P212 50.00 Full setpoint corresponds to 50%P323 1 Analogue input 2 (PID input) configured for 4 – 20 mAThe motor rating plate parameters correspond to a 1LA7 11 kW 4 pole motor connected in Star.(11kW)Siemens DA 64 – 1998/99 (04/99) 4/11
MICROMASTERMICROMASTER VectorMIDIMASTER VectorCommunications/Interfaces5. User Interfaces 5/15.1 Communications, Operator Control and Visualization 5/15.2 Standard Operator Control Panel 5/15.3 Serial RS 485 Interface 5/15.4 Control Terminal Strips 5/25.5 Clear Text Display (Optional) 5/25.6 PROFIBUS Module CB15 5/45.7 CANbus Module 5/75.8 Control and Commissioning with SIMOVIS (Option) 5/75.9 Diagnostics, Fault Codes and Parameter Listings 5/105.10 Parameter List 5/11
Page 1 and 2:
MICROMASTERMICROMASTER VectorMIDIMA
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14: MICROMASTERMICROMASTER VectorMIDIMA
Page 55 and 56: Standard ApplicationsMICROMASTERMIC
Page 63: Standard ApplicationsMICROMASTERMIC
Page 67 and 68: Communications/InterfacesMICROMASTE
Page 89 and 90: Inverter Selection and Ordering Dat
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
COMBIMASTER & MICROMASTER Integrate
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
AppendixMICROMASTERMICROMASTER Vect
show all

MicroMaster 6SE92 - ECT Sales & Service

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?