SPW Product Catalogue 2019

More documents

Recommendations

Info

WELDING TYPES, POSITIONS & DEFECTS HOW WELDING SYMBOLS ARE USED TYPE OF WELD SKETCH OF WELD SYMBOL INDICATION OF DRAWING FILLET WELD BEAD EDGE WELD SEAL WELD BACKING RUN BUTT WELDS GENERAL BUTT FULL PENETRATION BUTT WELD BY A WELDING PROCEDURE TO BE AGREED SQUARE BUTT 6 SINGLE 'V' BUTT SINGLE BEVEL BUTT SINGLE 'U' BUTT SINGLE 'J' BUTT TYPE OF WELD SKETCH OF WELD SYMBOL INDICATION OF DRAWING PUG OR SLOT STUD SURFACING WELD FINISH TYPE OF WELD SYMBOL INDICATION OF DRAWING SKETCH OF WELD FLUSH FINISH CONVEX FINISH CRANKED ARROW TECHNICAL A. A CRANKED ARROW IS USED WITH A BEVEL OR "J" WELD SYMBOL POINTING TOWARD THE PLATE WHICH IS PREPARED. SEE 1 B. IF THE PLATE TO BE PREPARED IS OBVIOUS THE CRANK IS OMMITED. SEE 2 1 2 Copyright Produced with the permission of CIGWELD 478 <strong>SPW</strong> GROUP PTY LTD
WELDING TYPES, POSITIONS & DEFECTS DEFECTS IN WELDING TYPES OF DEFECTS EXTERNAL DEFECTS: Can be identified by a visual inspection method eg: Dye Penetrant and Magnetic Particle testing. INTERNAL DEFECTS: Require a Non-Destructive testing (NDT) method eg: X-Ray or Ultrasonic testing. (i) Main Causes: Welding operators carelessness or lack of skill. Adverse working conditions (Hot Cold). Poor Design or lack of preparation. (ii) Main Defects: Undercut. Lack of fusion. Slag inclusions. Incomplete penetration. Porosity. Weld cracking. Overlap or over-roll. Joint Misalignment. UNDERCUT UNDERCUT Definition: A groove at the toe or root of a weld either on the weld face or in previously deposited weld metal. Causes: Excessive amperage. Too long an arc length . Excessive weaving of the electrode. Too fast a rate of travel. Angle of electrode too inclined to the joint face. Result: A stress concentration site and a potential site for fatigue 6 OVERLAP OR OVER-ROLL Definition: An imperfection at the toe or root of a weld caused by metal flowing onto the surface of the parent metal without fusing to it. OVERLAP OVERLAP Causes: Incorrect rate of travel. Incorrect “angle of approach”. Too large an electrode size. Too low an amperage. Result Has a similar effect as undercut and produces a stress concentration site due to the unfused weld metal. SLAG INCLUSIONS Definition: Refers to any non-metallic material in a completed weld joint. These inclusions can create a weak point in the weld deposit. SLAG INCLUSIONS Causes: Failure to remove slag from previous runs. Insufficient amperage. Incorrect electrode angle or size. Faulty preparation. Result: Slag inclusions reduce the cross sectional area strength of the weld and serve as a potential site for cracking. TECHNICAL Copyright Produced with the permission of CIGWELD 1300 WELDER (1300 935 337) 479
Page 1 and 2:
AUST: 1300 WELDER (935 337) NZ: 080
Page 3:
WELDING EQUIPMENT GAS EQUIPMENT IND
Page 6 and 7:
ACCESSORIES 1 ELECTRODE HOLDERS TWI
Page 8 and 9:
ACCESSORIES 1 LENCO® GROUND CLAMPS
Page 10 and 11:
ACCESSORIES 1 WORK CLAMPS SPRING LO
Page 12 and 13:
1 ACCESSORIES COOL ARC® 20 Item Nu
Page 14 and 15:
ACCESSORIES 1 WELDING EQUIPMENT PRO
Page 16 and 17:
1 ACCESSORIES L.I.T. PROCESS A safe
Page 18 and 19:
ACCESSORIES 1 TIG CHAMP BRUSH DC PL
Page 20 and 21:
1 ACCESSORIES CERAMIC BACKING BAR C
Page 22 and 23:
1 ACCESSORIES TIP CLEANERS Part No.
Page 24 and 25:
1 ACCESSORIES HAND TOOLS 330-B SMAL
Page 26 and 27:
1 WELDING EQUIPMENT ACCESSORIES ARC
Page 28 and 29:
1 ACCESSORIES K112 & K113 SUB ARC G
Page 30 and 31:
ACCESSORIES 1 ARC GOUGING TORCHES P
Page 32 and 33:
ACCESSORIES 1 K231 SUB ARC ASSEMBLY
Page 34 and 35:
ACCESSORIES 1 CONTOUR® & CURV O MA
Page 36 and 37:
1 ACCESSORIES SUMNER ULTRA CLAMPS -
Page 38 and 39:
ACCESSORIES 1 SINGLE JACKSCREW CHAI
Page 40 and 41:
1 ACCESSORIES RIM CLAMPS WARNINGS:
Page 42 and 43:
ACCESSORIES 1 SADDLE MACHINE Depend
Page 44 and 45:
ACCESSORIES 1 MONARCH BAND PIPE CUT
Page 46 and 47:
1 ACCESSORIES PIPE WRAP The Mathey
Page 48 and 49:
ACCESSORIES TRI TOOL INC. 1 PIPE BE
Page 50 and 51:
ACCESSORIES TRI TOOL INC. 1 1” TO
Page 52 and 53:
ACCESSORIES TRI TOOL INC. 1 TRI TOO
Page 54 and 55:
ACCESSORIES 1 ARDROX 907PB ARDROX 9
Page 56 and 57:
MMAW (STICK) WELDERS EURO No4 415V
Page 58 and 59:
20 3.6 No MMAW (STICK) WELDERS 20 2
Page 60 and 61:
415V AUX 5kVA 240V AUX 4kVA CUT 16m
Page 62 and 63:
1 STICK WELDERS INVERTEC® K12040-2
Page 64 and 65:
1 STICK WELDERS Minarc Evo 150 & 14
Page 66 and 67:
20 3.6 TIG WELDERS 20 3.6 20 3.6 20
Page 68 and 69:
TIG WELDERS 20 3.6 20 3.6 20 3.6 1
Page 70 and 71:
1 TIG WELDERS INVERTEC® V160-TP K1
Page 72 and 73:
1 TIG WELDERS INVERTEC® V270-T AC/
Page 74 and 75:
TIG WELDERS 1 Mastertig MLS TM 3000
Page 76 and 77:
TIG WELDERS 1 MASTERTIG MLS 3000 AC
Page 78 and 79:
TIG TORCHES AND SPARES 1 TM9 CONSUM
Page 80 and 81:
TIG TORCHES AND SPARES 1 TM18 CONSU
Page 82 and 83:
TIG TORCHES AND SPARES 1 TM24 CONSU
Page 84 and 85:
TIG TORCHES AND SPARES 1 TIGMASTER
Page 86 and 87:
TIG TORCHES AND SPARES 1 TIG WELDIN
Page 88 and 89:
TIG TORCHES AND SPARES 1 TTC TIG-TO
Page 90 and 91:
1 TIG TORCHES AND SPARES TUNGSTEN E
Page 92 and 93:
1 MIG WELDERS WeldSkill 250 MIG Por
Page 94 and 95:
20 3.6 MIG WELDERS 20 3.6 20 3.6 1
Page 96 and 97:
20 3.6 MIG WELDERS 20 20 3.6 3.6 1
Page 98 and 99:
MIG WELDERS 1 SYNERGIC PULSE Intell
Page 100 and 101:
MIG WELDERS 20 3.6 20 3.6 20 3.6 1
Page 102 and 103:
1 MIG WELDERS CV425 - CV510 Shown w
Page 104 and 105:
MIG WELDERS 1 KEMPACT RA 181A, 251R
Page 106 and 107:
MIG WELDERS 1 FASTMIG PULSE 350/450
Page 108 and 109:
1 MIG WELDERS MAGTRAC F 61 Kemppi
Page 110 and 111:
1 Wire guide tube Wire ø mm 0.6 0.
Page 112 and 113:
MIG WELDERS 1 Weldmatic 190 Part No
Page 114 and 115:
MIG TORCHES AND SPARES 1 WELDING EQ
Page 116 and 117:
MIG TORCHES AND SPARES 1 TWECO® No
Page 118 and 119:
MIG TORCHES AND SPARES 1 SPARE PART
Page 120 and 121:
MIG TORCHES AND SPARES 1 CONTACT TI
Page 122 and 123:
MIG TORCHES AND SPARES 1 TWECO® NO
Page 124 and 125:
MIG TORCHES AND SPARES 1 MIG GUN LI
Page 126 and 127:
MIG TORCHES AND SPARES 1 1150 SELF
Page 128 and 129:
MIG TORCHES AND SPARES 1 PROFAX HEA
Page 130 and 131:
MIG TORCHES AND SPARES 1 130GL SELF
Page 132 and 133:
MIG TORCHES AND SPARES 1 PROFAX® R
Page 134 and 135:
MIG TORCHES AND SPARES 1 CONSUMABLE
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
MIG TORCHES AND SPARES 1 MIG/MAG WE
Page 142 and 143:
MIG TORCHES AND SPARES 1 MIG/MAG WE
Page 144 and 145:
MIG TORCHES AND SPARES 1 BERNARD MI
Page 146 and 147:
MIG TORCHES AND SPARES 1 LINERS WIR
Page 148 and 149:
MULTI-PROCESS WELDERS 20 3.6 20 3.6
Page 150 and 151:
20 3.6 MULTI-PROCESS WELDERS 20 3.6
Page 152 and 153:
20 3.6 MULTI-PROCESS WELDERS 20 20
Page 154 and 155:
1 WELDING EQUIPMENT MULTI-PROCESS W
Page 156 and 157:
MULTI-PROCESS WELDERS 20 3.6 20 3.6
Page 158 and 159:
ENGINE DRIVEN WELDERS 20 3.6 1 OUTB
Page 160 and 161:
ENGINE DRIVEN WELDERS 20 3.6 1 Vant
Page 162 and 163:
1 WIRE FEEDERS TRANSMIG VA4000 Part
Page 164 and 165:
WIRE FEEDERS 1 LF-72 and LF-74 Wire
Page 166 and 167:
1 WIRE FEEDERS LN-25 PRO K2614-1 K2
Page 168 and 169:
PLASMA 1 CUTSKILL 35A PLASMA INVERT
Page 170 and 171:
1 WELDING EQUIPMENT PLASMA CUTMASTE
Page 172 and 173:
PLASMA TORCHES AND SPARES 1 HAND TO
Page 174 and 175:
PLASMA TORCHES AND SPARES 1 PLASMA
Page 176 and 177:
PLASMA TORCHES AND SPARES 1 PCH/M-8
Page 178 and 179:
PLASMA TORCHES AND SPARES 1 PCT 20
Page 180 and 181:
PLASMA TORCHES AND SPARES 1 T100 TO
Page 182 and 183:
PLASMA TORCHES AND SPARES 1 PT-25 P
Page 184 and 185:
PLASMA TORCHES AND SPARES 1 PLASMA
Page 186 and 187:
PURGING 1 ARGWELD INFLATABLE PIPE P
Page 188 and 189:
PURGING 1 ARGWELD PIPE PURGE PLUGS
Page 190 and 191:
PORTABLE OVENS 1 INDUSTRIAL WELDING
Page 192 and 193:
SPECIALISED WELDERS 1 ROBOTS Purcha
Page 194 and 195:
1 AUTOMATION BOA-408i S4 package Th
Page 196 and 197:
AUTOMATION 1 TOOL POSITIONING SYSTE
Page 198 and 199:
1 AUTOMATION SPEED WEAVER II The Sp
Page 200 and 201:
AUTOMATION 1 BUG-GY FILLET WELDER A
Page 202 and 203:
AUTOMATION 1 BENT RIGID RAILS (BRR)
Page 204 and 205:
AUTOMATION 1 WELDING CHUCK Bigger w
Page 206 and 207:
1 AUTOMATION VRX INTERNAL VRD The i
Page 208 and 209:
AUTOMATION 1 FLUX RECOVERY MADE EA$
Page 210 and 211:
AUTOMATION 1 SPS-1500 (11⁄2HP), S
Page 212 and 213:
AUTOMATION 1 MAGNATECH 800 SERIES W
Page 214 and 215:
AUTOMATION 1 MAGNATECH TUBESHEET WE
Page 216 and 217:
1 AUTOMATION MAGNATECH PIPEMASTER 5
Page 218 and 219:
1 AUTOMATION MAGNATECH PIPELINER II
Page 220 and 221:
AUTOMATION 1 MAGNATECH WELDING TRAC
Page 222 and 223:
KITS COMET EDGE CUSTOM 4 PACK 2 Par
Page 224 and 225:
KITS REGULATORS - WELDING, CUTTING,
Page 226 and 227:
KITS GAS EQUIPMENT TURBOTORCH® 2 E
Page 228 and 229:
2 REGULATORS COMET EDGE ESS3 CO2 RE
Page 230 and 231:
2 REGULATORS COMET EDGE ESS4 NITROG
Page 232 and 233:
REGULATORS GENUINE COMET 5000 HIGH
Page 234 and 235:
REGULATORS CUTSKILL OXYGEN REGULATO
Page 236 and 237:
BLOWPIPES AND ATTACHMENTS GENUINE C
Page 238 and 239:
BLOWPIPES AND ATTACHMENTS 2 GENUINE
Page 240 and 241:
BLOWPIPES AND ATTACHMENTS 2 GENUINE
Page 242 and 243:
CUTTING NOZZLES GENUINE COMET TYPE
Page 244 and 245:
CUTTING NOZZLES CUTSKILL TYPE 41 CU
Page 246 and 247:
WELDING AND HEATING GENUINE COMET O
Page 248 and 249:
WELDING AND HEATING GENUINE COMET S
Page 250 and 251:
HOSES AND FITTINGS FITTED HOSES AND
Page 252 and 253:
HOSES AND FITTINGS TWIN GAS HOSES (
Page 254 and 255:
2 ACCESSORIES GENUINE COMET FLASHBA
Page 256 and 257:
ACCESSORIES FLINT LIGHTER Metal Cup
Page 258 and 259:
MACHINES 2 PIPEMATE Specifications
Page 260 and 261:
GAS HEATING HANDPIECE 2 EXPANSION B
Page 262 and 263:
GAS HEATING SIEVERT FLOWCHART 2 NEC
Page 264 and 265:
INDUSTRIAL GASES These pages have b
Page 266 and 267:
GASES Shielding gas selection chart
Page 268 and 269:
GASES SHIELDING GASES 3 MCW INDUSTR
Page 270 and 271:
GASES SHIELDING GASES 3 Heavy INDUS
Page 272 and 273:
GASES SHIELDING GASES Copper INDUST
Page 274 and 275:
RESPIRATORY CLEANSPACE2 POWERED RES
Page 276 and 277:
RESPIRATORY PROTECTION REUSABLE RES
Page 278 and 279:
HEAD AND FACE 3M VERSAFLO FACE SHIE
Page 280 and 281:
HEAD AND FACE HELMETS AND PARTS D63
Page 282 and 283:
HEAD AND FACE HIDEROK WELDING HELME
Page 284 and 285:
HEAD AND FACE WELDING GOGGLES PART
Page 286 and 287:
HEAD AND FACE DISPOSABLE & REUSABLE
Page 288 and 289:
HEAD AND FACE 3M VERSAFLO 4 3M VERS
Page 290 and 291:
HEAD AND FACE WORKPLACE EYEWEAR UVE
Page 292 and 293:
HEAD AND FACE WORKPLACE EYEWEAR UVE
Page 294 and 295:
HEAD AND FACE UVEX EYEWEAR ACCESSOR
Page 296 and 297:
HEAD AND FACE WORKPLACE EYEWEAR ONI
Page 298 and 299:
HAND PROTECTION MARKING AS PER AS/N
Page 300 and 301:
HAND PROTECTION GLOVES RIGGER GLOVE
Page 302 and 303:
HAND PROTECTION WELDING GLOVES SUPE
Page 304 and 305:
HAND PROTECTION KEVLAR® HEAT PROTE
Page 306 and 307:
WELDING & GENERAL APPAREL CHROME LE
Page 308 and 309:
WELDING & GENERAL APPAREL BIG RED®
Page 310 and 311:
WELDING & GENERAL APPAREL WAKATAC S
Page 312 and 313:
WELDING & GENERAL APPAREL CHROME LE
Page 314 and 315:
WELDING BLANKETS & DRAPES WELDING D
Page 316 and 317:
FUME EQUIPMENT MINIVEYOR AIR VAF CO
Page 318 and 319:
ELECTRODES MILD STEEL & IRON POWDER
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
ELECTRODES LOW HYDROGEN 5 FERROCRAF
Page 330 and 331:
ELECTRODES LOW HYDROGEN FERROCRAFT
Page 332 and 333:
ELECTRODES LOW HYDROGEN ALLOYCRAFT
Page 334 and 335:
ELECTRODES LOW HYDROGEN EASYARC TM
Page 336 and 337:
ELECTRODES LOW HYDROGEN KRYO® 3 Lo
Page 338 and 339:
ELECTRODES LOW HYDROGEN KOBE ELECTR
Page 340 and 341:
ELECTRODES LOW HYDROGEN OK 53.70 Ty
Page 342 and 343:
ELECTRODES LOW HYDROGEN OK 74.46 (N
Page 344 and 345:
ELECTRODES LOW HYDROGEN OK 76.18 Ty
Page 346 and 347:
ELECTRODES LOW HYDROGEN AUSTARC 16T
Page 348 and 349:
ELECTRODES STAINLESS STEEL & SPECIA
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
ELECTRODES HARD FACING COBALARC AUS
Page 364 and 365:
ELECTRODES HARD FACING 5 COBALARC 7
Page 366 and 367:
ELECTRODES HARD FACING 5 STOODY TUB
Page 368 and 369:
WIRES MIG AUTOCRAFT LW1 ALL POSITIO
Page 370 and 371:
WIRES MIG AUTOCRAFT MN-MO ALL POSIT
Page 372 and 373:
WIRES MIG AUTOCRAFT 309LSi ALL POSI
Page 374 and 375:
WIRES MIG AUTOCRAFT AL5356 ALL POSI
Page 376 and 377:
WIRES MIG 5 CONSUMABLES 374 AVESTA
Page 378 and 379:
WIRES MIG SM-70 CO 2 /Ar+CO 2 5 AWS
Page 380 and 381:
WIRES MIG SM-308L AWS A5.9 / ASME S
Page 382 and 383:
WIRES MIG LINCOLN 308LSi Designed f
Page 384 and 385:
WIRES FLUX CORED SATIN-COR XP 5 Sat
Page 386 and 387:
5 WIRES FLUX CORED VERTI-COR 3XP Ve
Page 388 and 389:
5 WIRES FLUX CORED VERTI-COR 111 K3
Page 390 and 391:
WIRES FLUX CORED NICORE® 55 5 Nico
Page 392 and 393:
WIRES FLUX CORED STOODY SOS 308L 5
Page 394 and 395:
(Gas Shielded) FLUX CORED WIRES OUT
Page 396 and 397:
WIRES FLUX CORED INNERSHIELD® NR-2
Page 398 and 399:
WIRES FLUX CORED KOBE FLUX CORED WI
Page 400 and 401:
WIRES FLUX CORED SF-71 CO 2 5 AWS A
Page 402 and 403:
WIRES FLUX CORED SUPERCORED 70B CO
Page 404 and 405:
WIRES FLUX CORED SC-80D2 CO 2 AWS A
Page 406 and 407:
WIRES FLUX CORED DUAL SHIELD 7100 A
Page 408 and 409:
WIRES FLUX CORED DUAL SHIELD II 110
Page 410 and 411:
WIRES FLUX CORED COREWELD 111 ULTRA
Page 412 and 413:
WIRES FLUX CORED SHIELD-BRIGHT 308L
Page 414 and 415:
WIRES FLUX CORED SHIELD-BRIGHT 316L
Page 416 and 417:
WIRES HARD FACING 5 STOODY DYNAMANG
Page 418 and 419:
WIRES HARD FACING 5 STOODY 101 HC-G
Page 420 and 421:
WIRES HARD FACING LINCORE® 33 Prov
Page 422 and 423:
WIRES HARD FACING LINCORE® 60-O Re
Page 424 and 425:
SUB ARC WIRES AND FLUXES AUTOCRAFT
Page 426 and 427:
SUB ARC WIRES AND FLUXES QR-8045 Al
Page 428 and 429:
SUB ARC WIRES AND FLUXES LINCOLNWEL
Page 430 and 431: SUB ARC WIRES AND FLUXES 8500 A hig
Page 432 and 433: SUB ARC WIRES AND FLUXES 5 CONSUMAB
Page 434 and 435: SUB ARC WIRES AND FLUXES OK FLUX 10
Page 436 and 437: SUB ARC WIRES AND FLUXES OK FLUX 10
Page 438 and 439: SUB ARC WIRES AND FLUXES OK AUTROD
Page 440 and 441: GAS AND TIG CONSUMABLES COMWELD LW1
Page 442 and 443: GAS AND TIG CONSUMABLES COMWELD CRM
Page 444 and 445: GAS AND TIG CONSUMABLES COMWELD AL1
Page 446 and 447: GAS AND TIG CONSUMABLES COMWELD GEN
Page 448 and 449: GAS AND TIG CONSUMABLES COMWELD TOB
Page 450 and 451: GAS AND TIG CONSUMABLES COMWELD SIL
Page 452 and 453: GAS AND TIG CONSUMABLES LINCOLN 446
Page 454 and 455: GAS AND TIG CONSUMABLES AVESTA STAN
Page 456 and 457: ABRASIVES FLAT METAL CUTTING OFF WH
Page 458 and 459: ABRASIVES METAL DEPRESSED CENTRE GR
Page 460 and 461: ABRASIVES INDUSTRIAL WIRE BRUSHES T
Page 462 and 463: ABRASIVES INDUSTRIAL COATED ABRASIV
Page 464 and 465: ABRASIVES INDUSTRIAL COATED ABRASIV
Page 466 and 467: OTHER COMWELD 965 SOLDER (SOFT SILV
Page 468 and 469: OTHER COMWELD 965 SOLDERING FLUX CO
Page 470 and 471: CHEMICAL PRODUCTS AVESTA REDONE 240
Page 472 and 473: CHEMICAL PRODUCTS 5 Avesta RedOne 1
Page 474 and 475: TERMS & DEFINITIONS TERMS AND DEFIN
Page 476 and 477: WELDING TYPES, POSITIONS & DEFECTS
Page 486 and 487: SAFETY IN WELDING A) ARC RADIATION
Page 488 and 489: CONSUMABLES CLASSIFICATION TABLES A
Page 502 and 503: WELDING GUIDE GENERAL PROCEDURE IN
Page 504 and 505: WELDING GUIDE PREHEAT DETERMINATION
Page 506 and 507: WELDING GUIDE STEEL SPECIFICATIONS
Page 512 and 513: WELDING GUIDE WELDING RECOMMENDATIO
Page 514 and 515: WELDING GUIDE CONSUMABLES FOR WELDI
Page 516 and 517: WELDING GUIDE AUSTENITIC STAINLESS
Page 518 and 519: WELDING GUIDE HEAT INPUT When the w
Page 520 and 521: WELDING GUIDE SCHAEFFLER AND DE LON
Page 522 and 523: WELDING GUIDE DEW POINT CONDITIONS
Page 524 and 525: WELDING GUIDE 3) FEEDABILITY OF ALU
Page 526 and 527: WELDING GUIDE 4) SMOKE TESTING ALUM
Page 528 and 529: WELDING GUIDE 5) ARC LENGTH & HEAT
Page 530 and 531:
WELDING GUIDE ALUMINIUM ALLOY SELEC
Page 532 and 533:
WELDING GUIDE 1) ALUMINIUM BASE MET
Page 534 and 535:
WELDING GUIDE 2) TUNGSTEN ELECTRODE
Page 536 and 537:
WELDING GUIDE 5) GTAW (TIG) TECHNIQ
Page 538 and 539:
WELDING GUIDE TYPES OF CAST IRON CO
Page 540 and 541:
WELDING GUIDE PRECAUTIONS WHEN WELD
Page 542 and 543:
WELDING GUIDE SG CAST IRON Grey iro
Page 544 and 545:
WELDING GUIDE 1) TYPES OF COPPER AL
Page 546 and 547:
WELDING GUIDE 3) GAS METAL ARC WELD
Page 548 and 549:
WELDING GUIDE 7) BRAZE WELDING OF C
Page 550 and 551:
HARDFACING INFORMATION WHAT IS HARD
Page 552 and 553:
HARDFACING INFORMATION HOW TO CHOOS
Page 554 and 555:
HARDFACING INFORMATION COBALARC PRO
Page 556 and 557:
HARDFACING INFORMATION COBALARC APP
Page 558 and 559:
HARDFACING INFORMATION USE OF BUFFE
Page 560 and 561:
WELD COSTINGS COSTING INFORMATION:
Page 562 and 563:
DEPOSITION DATA GENERAL PROCESS EFF
Page 564 and 565:
DEPOSITION DATA SQUARE BUTT JOINTS,
Page 566 and 567:
FACTS & FIGURES MATHEMATICAL SYMBOL
Page 568 and 569:
FACTS & FIGURES COMMON WELDING CONV
Page 570 and 571:
FACTS & FIGURES CONVERSION TABLES -
Page 572 and 573:
FACTS & FIGURES COMWELD RODS PER KG
Page 574 and 575:
FACTS & FIGURES MASSES OF COMMON ME
Page 576 and 577:
FACTS & FIGURES TEMPERATURE CONVERS
Page 578 and 579:
FACTS & FIGURES GAS PRESSURES - GAS
Page 580 and 581:
INFORMATION CONNECTORS SHELL Shell
Page 582 and 583:
6 WARRANTY DATA LINCOLN ELECTRIC AU
Page 584 and 585:
6 TECHNICAL 582 SPW GROUP PTY LTD
Page 586 and 587:
IMPORTANT SAFETY INFORMATION IMPORT
Page 588 and 589:
Guarantee and indemnity i/We: (here
Page 590 and 591:
General terms and conditions of Sup
Page 592 and 593:
NOTES 590 SPW GROUP PTY LTD
Page 594 and 595:
NOTES 592 SPW GROUP PTY LTD
Page 596:
WE HAVE THE BEST WELDING EQUIPMENT
show all

SPW Product Catalogue 2019

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?