The Virtualization Cookbook for SLES 10 SP2 - z/VM - IBM
The Virtualization Cookbook for SLES 10 SP2 - z/VM - IBM
The Virtualization Cookbook for SLES 10 SP2 - z/VM - IBM
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
► Verify that the new user IDs have access with the QUERY VSWITCH ACCESSLIST command:<br />
==> query vswitch vsw1 acc<br />
VSWITCH SYSTEM VSW1 Type: VSWITCH Connected: 4 Maxconn: INFINITE<br />
PERSISTENT RESTRICTED NONROUTER Accounting: OFF<br />
VLAN Unaware<br />
State: Ready<br />
IPTimeout: 5 QueueStorage: 8<br />
Portname: UNASSIGNED RDEV: 3004 Controller: DTCVSW1 VDEV: 3004<br />
Portname: UNASSIGNED RDEV: 3008 Controller: DTCVSW2 VDEV: 3008 BACKUP<br />
Authorized userids:<br />
LINUX01 LINUX02 LINUX03 LINUX04 RH6CLONE RH6GOLD<br />
SYSTEM<br />
...<br />
9.5.4 Testing logging on to a new user ID<br />
You should now be able to logon to a new user ID and verify the integrity of the definitions.<br />
Per<strong>for</strong>m the following steps<br />
► Logon to LINUX02 and you should first notice that a NIC is created as well as two<br />
VDISKs:<br />
LOGON LINUX02<br />
00: NIC 0600 is created; devices 0600-0602 defined<br />
z/<strong>VM</strong> Version 6 Release 1.0, Service Level <strong>10</strong>02 (64-bit),<br />
built on <strong>IBM</strong> <strong>Virtualization</strong> Technology<br />
<strong>The</strong>re is no logmsg data<br />
FILES: NO RDR, NO PRT, NO PUN<br />
LOGON AT 11:05:06 EDT TUESDAY <strong>10</strong>/05/<strong>10</strong><br />
z/<strong>VM</strong> V6.1.0 20<strong>10</strong>-09-23 11:31<br />
DMSACP723I A (191) R/O<br />
DMSACP723I C (592) R/O<br />
DIAG swap disk defined at virtual address 300 (64989 4K pages of swap space)<br />
DIAG swap disk defined at virtual address 301 (129981 4K pages of swap space)<br />
Do you want to IPL Linux from minidisk <strong>10</strong>0? y/n<br />
n<br />
If you <strong>for</strong>got to grant access to the VSWITCH you will see an error message.<br />
► Verify that you have two read/write devices at addresses <strong>10</strong>0-<strong>10</strong>1 with the QUERY DASD<br />
command:<br />
==> q da<br />
DASD 0<strong>10</strong>0 3390 UM63AA R/W 3338 CYL ON DASD 63AA SUBCHANNEL = 0000<br />
DASD 0<strong>10</strong>1 3390 UM63AA R/W 3338 CYL ON DASD 63AA SUBCHANNEL = 0001<br />
...<br />
► Logoff of LINUX02.<br />
Congratulations, you have cloned one Linux virtual server and defined three more user IDs<br />
that should now be ready <strong>for</strong> cloning to. You will clone to these user IDs in the chapter that<br />
follows. In addition to cloning, the Red Hat kickstart tool can also be used. That is discussed<br />
in Chapter <strong>10</strong>, “Installing Linux with kickstart” on page 163.<br />
9.6 Reviewing system status<br />
You can step back now and view your system from a DASD point of view as shown in<br />
Figure 9-2. If you have followed all sections in this book you should have used the equivalent<br />
160 <strong>The</strong> <strong>Virtualization</strong> <strong>Cookbook</strong> <strong>for</strong> RHEL 6