The Virtualization Cookbook for SLES 10 SP2 - z/VM - IBM
The Virtualization Cookbook for SLES 10 SP2 - z/VM - IBM
The Virtualization Cookbook for SLES 10 SP2 - z/VM - IBM
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
One default setting that can be dangerous, especially if you use F12 to retrieve commands, is<br />
that PF12 is set to the FILE subcommand. Sometimes you may not want to save your<br />
changes with the stroke of one key. It is recommended that you set PF12 to the ?<br />
subcommand which has the effect of a retrieve key:<br />
==> copy profile xedit a profile xediorig a (oldd<br />
==> x profile xedit a<br />
Be<strong>for</strong>e:<br />
After:<br />
SET PF12 FILE<br />
SET PF12 ?<br />
Save your changes with the FILE subcommand.<br />
4.4 Customizing the SYSTEM CONFIG file<br />
<strong>The</strong> first configuration file read when z/<strong>VM</strong> IPLs is the SYSTEM CONFIG file. <strong>The</strong> following<br />
changes are recommended:<br />
► Change the system name<br />
► Increase retrieve key capacity<br />
► Allow virtual disks (VDISKs) to be created<br />
► Turn off the Disconnect Timeout (this will prevent idle disconnected users from being<br />
<strong>for</strong>ced off the system)<br />
► Define a virtual switch (VSWITCH) that will be used <strong>for</strong> Linux networking<br />
To make these changes, per<strong>for</strong>m the following steps:<br />
► To edit the SYSTEM CONFIG file, the MAINT CF1 minidisk must be released as a CP disk<br />
using the CPRELASE command. <strong>The</strong> CP disks are queried using the QUERY CPDISK command.<br />
Note the MAINT CF1 disk is accessed as CP disk A be<strong>for</strong>e it is released but not after.<br />
==> q cpdisk<br />
Label Userid Vdev Mode Stat Vol-ID Rdev Type StartLoc EndLoc<br />
MNTCF1 MAINT 0CF1 A R/O 6<strong>10</strong>RES 6280 CKD 39 158<br />
MNTCF2 MAINT 0CF2 B R/O 6<strong>10</strong>RES 6280 CKD 159 278<br />
MNTCF3 MAINT 0CF3 C R/O 6<strong>10</strong>RES 6280 CKD 279 398<br />
==> cprel a<br />
CPRELEASE request <strong>for</strong> disk A scheduled.<br />
HCPZAC6730I CPRELEASE request <strong>for</strong> disk A completed.<br />
==> q cpdisk<br />
Label Userid Vdev Mode Stat Vol-ID Rdev Type StartLoc EndLoc<br />
MNTCF2 MAINT 0CF2 B R/O 6<strong>10</strong>RES 6280 CKD 159 278<br />
MNTCF3 MAINT 0CF3 C R/O 6<strong>10</strong>RES 6280 CKD 279 398<br />
► Once it is released you are able to access the MAINT CF1 disk read-write. Use the LINK<br />
command with multi-read (MR) parameter and ACCESS command to get read-write access<br />
as your F disk.<br />
==> link * cf1 cf1 mr<br />
==> acc cf1 f<br />
► Make a backup copy of the vanilla SYSTEM CONFIG file using the COPYFILE command with<br />
the OLDDATE parameter so the timestamp of the file is not modified. Note that because the<br />
target file name (system) and mode (f) are the same, the equal sign (=) can be used as a<br />
wildcard.<br />
44 <strong>The</strong> <strong>Virtualization</strong> <strong>Cookbook</strong> <strong>for</strong> RHEL 6