Urma Digiset 5 USERMANUAL - Urma AG

More documents

Recommendations

Info

digiset 5 4.2 Calibration of Presetter 4.2.1 Set the camera’s working distance The working distance is defined as the distance between the front edge of the camera tube shield and the object to be measured, for example a tool cutting edge. This measurement is preset by the design and the production tolerances of the camera tube shield (lens). The working distance must be set following the instructions in the enclosed calibration log with a permissible tolerance of 100 ± 0.1mm. (3.937 ± .004”) Optical axis Illumination Aligning the camera and the lamp Object to be measured Working distance Camera Urma AG, Switzerland www.urma.ch page 12
digiset 5 4.2.2 Check illumination After the working distance is checked, the homogeneity and brightness of the illumination must be set. For this, you must not have anything in the camera’s visual field. To check the illumination the greyscales are checked in the camera’s horizontal and vertical alignment on both edges of the image as well as the middle of the image and the results shown on 6 lines. The illumination reaches its optimum setting if these lines are as horizontal as possible and within the horizontal tolerance range marked by 2 purple lines. You access the operating mode for setting the illumination using the following menu steps: Main menu Sub-menu 1 Sub-menu 2 Setup � Imaging � Illumination The TCAM2 displays the following image with 6 grey scales (illumination lines): Tolerance field Procedure: 1. Select the illumination check with the "Illumination" operating mode. The horizontal tolerance field appears with the illumination lines. "Illumination" appears in the status window. 2. If not all 6 greyscale lines on the LCD are inside the tolerance field, you have to adjust the light source. Remove the cover of the light source as shown on the picture below. Urma AG, Switzerland www.urma.ch page 13
Page 1 and 2: Urma Digiset 5 USERMANUAL Version 1
Page 3 and 4: digiset 5 Table of contents 1 IMPOR
Page 5 and 6: digiset 5 1 Important notes 1.1 Del
Page 7 and 8: digiset 5 2 Safety instructions 2.1
Page 9 and 10: digiset 5 4 SETUP INSTRUCTIONS 4.1
Page 11: digiset 5 6. Flip the Digiset to it
Page 15 and 16: digiset 5 4.2.3 Align camera When a
Page 17 and 18: digiset 5 4.2.5 Set absolute zero p
Page 19 and 20: digiset 5 5.1.1 Menu bar (Main menu
Page 21 and 22: digiset 5 • If no measurement fun
Page 23 and 24: digiset 5 5.2.2 Various methods of
Page 25 and 26: digiset 5 6 Configuration (software
Page 27 and 28: digiset 5 6.2.3 Brightness (optiona
Page 29 and 30: digiset 5 6.4 Output format You acc
Page 31 and 32: digiset 5 6.6 Corrections 6.6.1 Lin
Page 33 and 34: digiset 5 6.9 Date and time (option
Page 35 and 36: digiset 5 7.1.2.2 Delete tool refer
Page 37 and 38: digiset 5 7.2.2.2 Delete tool After
Page 39 and 40: digiset 5 7.4 Post processor-measur
Page 41 and 42: digiset 5 8 Imaging For each measur
Page 43 and 44: digiset 5 8.2.2 Maximum The measuri
Page 45 and 46: digiset 5 8.2.4 Measure centre Here
Page 47 and 48: digiset 5 8.3.2 Detailed descriptio
Page 49 and 50: digiset 5 8.3.2.5 "Line 1 - Point X
Page 51 and 52: digiset 5 8.4 Measuring programs /
Page 53 and 54: digiset 5 9 Index Adjustment bars 2

Urma Digiset 5 USERMANUAL - Urma AG

Create successful ePaper yourself

Delete template?

Save as template?