PowerFlex 755 Install Manual.pdf

More documents

Recommendations

Info

104 Event Fault Configuration Auto No. Fault/Alarm Text Type Action Parameter Reset Description/Action(s) 264 Port 4 Checksum Resettable Coast A option module storage checksum failed. 265 Port 5 Checksum Fault Option data has been set to default values. 266 Port 6 Checksum 267 Port 7 Checksum 268 Port 8 Checksum 269 Port 9 Checksum 270 Port10 Checksum 271 Port11 Checksum 272 Port12 Checksum 273 Port13 Checksum 274 Port14 Checksum 291 HS Fan Life Configurable P493 Predictive maintenance function has reached the event level. [HSFan EventActn] Perform maintenance. 292 In Fan Life Configurable P500 [InFan EventActn] 293 MtrBrng Life Configurable P506 [MtrBrngEventActn] 294 MtrBrng Lube Configurable P510 [MtrLubeEventActn] 295 MachBrng Life Configurable P515 [MtrBrngEventActn] 296 MachBrng Lube Configurable P519 [MchLubeEventActn] 307 Port7InvalidCard Non-Reset Fault Coast Option not valid in that port. Remove option module. 308 Port8InvalidCard Non-Reset Fault Coast 313 ENet Checksum Resettable Coast Ethernet/IP storage checksum failed. Data set to default Fault values. 314 DLX Checksum Resettable Coast DeviceLogix storage checksum failed. Data set to default Fault values. 14037 Net IO Timeout Configurable P52 [DLX Prog Cond] DeviceLogix has been disabled. Important: Fault and Alarm event numbers between 3000 and 13999 are generated by a module installed in a port. Refer to Fault and Alarm Display Codes on page 98 for an explanation. Manually Clearing Faults Refer to the following publications for detailed fault and alarm information. Event Number Range Publication Title Publication Number 3000…12999 PowerFlex 750-Series AC Drives User Manual 750-UM001 13000…13999 PowerFlex 755 Drive Embedded EtherNet/IP Adapter User Manual 750COM-UM001 Step Key(s) 1. Press the “Clear” soft key to acknowledge the fault. The fault information will be removed so that you can use the HIM. CLR 2. Address the condition that caused the fault. The cause must be corrected before the fault can be cleared. 3. After corrective action has been taken, clear the fault by one of these methods: Press Stop (if running the drive will stop) Cycle drive power Select the “Clear” soft key on the HIM Diagnostic folder Faults menu. PowerFlex 750-Series Installation Instructions – Publication 750-IN001C-EN-P – September 2009
Common Symptoms and Corrective Actions Drive does not Start from Start or Run Inputs wired to the terminal block. Cause(s) Indication Corrective Action Drive is Faulted Flashing red status light Drive does not Start from HIM. Drive does not respond to changes in speed command. Clear fault. Press Stop Cycle power “Clear Faults” on the HIM Diagnostic menu. Incorrect input wiring. See page 69 for wiring None examples. 2 wire control requires Run, Run Forward, Run Reverse or Jog input. 3 wire control requires Start and Stop inputs. Verify 24 Volt Common is connected to Digital Input Common. Wire inputs correctly. Incorrect digital input programming. None Configure input function. • Mutually exclusive choices have been made (i.e., Jog and Jog Forward). • 2 wire and 3 wire programming may be conflicting. • Start configured without a Stop configured. Flashing yellow status light and “DigIn Cnfg B” or “DigIn Cnfg C” indication on LCD HIM. P936 [Drive Status 2] shows type 2 alarm(s). Resolve input function conflicts. Terminal block does not have control. None Check P324 [Logic Mask]. Cause(s) Indication Corrective Action Drive is configured for 2 wire level None Change P150 [Digital In Conf] to correct control. control function. Another device has Manual control. None Port does not have control. None Change P324 [Logic Mask] to enable correct port. Cause(s) Indication Corrective Action No value is coming from the source of the command. Incorrect reference source has been programmed. Incorrect Reference source is being selected via remote device or digital inputs. LCD HIM Status Line indicates “At Speed” and output is 0 Hz. PowerFlex 750-Series Installation Instructions – Publication 750-IN001C-EN-P – September 2009 105 1. If the source is an analog input, check wiring and use a meter to check for presence of signal. 2. Check P2 [Commanded SpdRef] for correct source. None 3. Check P545 [Spd Ref A Sel] for the source of the speed reference. 4. Reprogram P545 [Spd Ref A Sel] for correct source. None 5. Check P935 [Drive Status 1] bits 12 and 13 for unexpected source selections. 6. Check P220 [Digital In Sts] to see if inputs are selecting an alternate source. 7. Check configuration of P173-175 [DI Speed Sel X] functions.
Page 1 and 2:
Installation Instructions PowerFlex
Page 3 and 4:
Table of Contents Catalog Number Ex
Page 5 and 6:
Step 1 Read the General Precautions
Page 7 and 8:
PowerFlex 750-Series drives generat
Page 9 and 10:
Drive Frame Catalog Number Frame 2
Page 11 and 12:
Table 4 480 Volt Ratings - Watts Lo
Page 13 and 14:
Table 7 Drive Enclosure Ratings Enc
Page 15 and 16:
Figure 2 IP20, NEMA/UL Open Type Fr
Page 17 and 18:
Figure 4 NEMA/UL Type 1 Frames 2…
Page 19 and 20:
Figure 6 IP00, NEMA/UL Open Type Fr
Page 21 and 22:
1271.0 (50.04) 1221.0 (48.07) 881.8
Page 23 and 24:
Figure 10 IP54, NEMA/UL Type 12 Fra
Page 25 and 26:
Figure 12 IP54, NEMA/UL Type 12, Fr
Page 27 and 28:
495.5 (19.51) 457.8 (18.02) Figure
Page 29 and 30:
591.50 (23.287) 550.75 (21.683) 465
Page 31 and 32:
875.0 (34.45) 812.0 (31.97) 784.0 (
Page 33 and 34:
IP00, NEMA/UL Open Type Frame 6 Lif
Page 35 and 36:
Accessing the Terminals Opening the
Page 37 and 38:
Step 3 Wire the Drive Special Consi
Page 39 and 40:
Voltage Tolerance Nominal Line Nomi
Page 41 and 42:
Terminal Block Specifications Table
Page 43 and 44:
➎ ➍ ➌ ➊ ➋ Frame 6 Figure
Page 45 and 46:
Common Bus Power Wiring Power Termi
Page 47 and 48:
Common Bus Power Terminal Blocks Fr
Page 49 and 50:
Using 750-Series Drives with Regen
Page 51 and 52:
Table 19 400 Volt AC Input Protecti
Page 53 and 54: Drive Power Jumper Configuration Po
Page 55 and 56: Power Jumper Screw Removal and Stor
Page 57 and 58: Figure 34 Frame 7 Jumper Wire Locat
Page 59 and 60: Access Drive Control Pod 1. Remove
Page 61 and 62: PowerFlex 753 Main Control Board
Page 63 and 64: PowerFlex 755 Main Control Board
Page 65 and 66: Safety Enable Circuitry The drive s
Page 67 and 68: I/O Module 20-750-2262C-2R 20-750-2
Page 69 and 70: I/O Wiring Examples 51 Anlg In0 Hi
Page 71 and 72: Input/Output Connection Example Req
Page 73 and 74: Input/Output Connection Example Req
Page 75 and 76: Safe Torque Off Option Module 20-75
Page 77 and 78: Table 38 Safe Speed Monitor Paramet
Page 79 and 80: I/O Connection Example Encoder Sign
Page 81 and 82: Table 46 Dual Incremental Encoder P
Page 83 and 84: Table 49 Universal Feedback Increme
Page 85 and 86: Auxiliary Power Supply Option Modul
Page 87 and 88: ControlNet Option Module For comple
Page 89 and 90: Step 5 Start-Up Check List Prepare
Page 91 and 92: Navigate to Start-Up Menu Using the
Page 93 and 94: Soft Keys Up to five dynamic soft k
Page 95 and 96: Ports and Devices Drive Device Port
Page 97 and 98: Status Indicators PowerFlex 753 Pow
Page 99 and 100: Event Fault Configuration Auto No.
Page 101 and 102: Event Fault Configuration No. Fault
Page 103: Event Fault Configuration Auto No.
Page 107 and 108: Drive (Port 0) Parameter List Numbe
Page 109 and 110: Number Parameter Name Group 315 SLA
Page 111 and 112: 611 TrmPct RefA AnLo Speed Trim 612
Page 113 and 114: 944 Drive Temp C Status 945 At Limi
Page 115 and 116: Notes: PowerFlex 750-Series Install
show all

PowerFlex 755 Install Manual.pdf

Create successful ePaper yourself

Delete template?

Save as template?