PowerFlex 755 Install Manual.pdf

More documents

Recommendations

Info

58 Step 4 I/O Wiring Important points to remember about I/O wiring: Always use copper wire. Wire with an insulation rating of 600V or greater is recommended. Control and signal wires should be separated from power wires by at least 0.3 meters (1 foot). In order to maintain electrical safety for all user-accessible low voltage circuits (ELV and PELV circuits), I/O terminals designated for 24V or lower voltage must not be connected to a circuit of higher voltage or a circuit which is not adequately insulated from dangerous voltages with double or reinforced insulation within other connected equipment or wiring. In order to provide electrical safety for user-accessible low voltage I/O circuits which are referenced to earth (PELV circuits) and which may be touched simultaneously, care should be taken to provide a common earth reference for all equipment connected to the drive. Important: I/O terminals labeled “(–)” or “Common” are not referenced to earth ground and are designed to greatly reduce common mode interference. Grounding these terminals can cause signal noise. ! ATTENTION: Hazard of personal injury or equipment damage exists when using bipolar input sources. Noise and drift in sensitive input circuits can cause unpredictable changes in motor speed and direction. Use speed command parameters to help reduce input source sensitivity. I/O Terminal Blocks Table 22 I/O Terminal Block Specifications Wire Size Range Torque Strip Name Maximum Minimum Maximum Recommended Length 753 Control Module TB2 2.5 mm2 0.3 mm (14 AWG) 2 0.25 N m 0.2 N m 6 mm (28 AWG) (2.2 lb in) (1.8 lb in) (0.24 in.) 753 Control Module TB1 and 2.5 mm TB3 2 0.3 mm (14 AWG) 2 0.25 N m 0.2 N m 6 mm (28 AWG) (2.2 lb in) (1.8 lb in) (0.24 in.) 755 Control Module TB1 2.5 mm2 0.3 mm (14 AWG) 2 0.25 N m 0.2 N m 6 mm (28 AWG) (2.2 lb in) (1.8 lb in) (0.24 in.) 755 I/O Module TB1 2.5 mm2 0.3 mm (14 AWG) 2 0.25 N m 0.2 N m 6 mm (28 AWG) (2.2 lb in) (1.8 lb in) (0.24 in.) 755 I/O Module TB2 4.0 mm2 0.25 mm (12 AWG) 2 0.5 N m 0.4 N m 7 mm (24 AWG) (4.4 lb in) (3.5 lb in) (0.28 in.) Safe Torque Off 0.8 mm2 0.3 mm (18 AWG) 2 N/A 10 mm (28 AWG) (0.39 in.) Single Incremental Encoder 0.8 mm2 0.3 mm (18 AWG) 2 N/A 10 mm (28 AWG) (0.39 in.) Safe Speed Monitor TB1 and 2.5 mm TB2 2 0.25 mm (14 AWG) 2 0.25 N m 0.2 N m 6 mm (24 AWG) (2.2 lb in) (1.8 lb in) (0.24 in.) Dual Incremental Encoder 0.8 mm2 0.3 mm (18 AWG) 2 N/A 10 mm (28 AWG) (0.39 in.) Universal Feedback Module 0.8 mm2 0.3 mm (18 AWG) 2 N/A 10 mm (28 AWG) (0.39 in.) Auxiliary Power Supply TB1 2.5 mm2 0.3 mm (14 AWG) 2 0.25 N m 0.2 N m 6 mm (28 AWG) (2.2 lb in) (1.8 lb in) (0.24 in.) PowerFlex 750-Series Installation Instructions – Publication 750-IN001C-EN-P – September 2009
Access Drive Control Pod 1. Remove drive cover Frames 2…5 – Squeeze locking tabs and pull out bottom of cover. – Pull cover down and away from the chassis. Frames 6…7 – Loosen door screws. – Gently pry the door open to remove. PowerFlex 750-Series Installation Instructions – Publication 750-IN001C-EN-P – September 2009 59
Page 1 and 2:
Installation Instructions PowerFlex
Page 3 and 4:
Table of Contents Catalog Number Ex
Page 5 and 6:
Step 1 Read the General Precautions
Page 7 and 8: PowerFlex 750-Series drives generat
Page 9 and 10: Drive Frame Catalog Number Frame 2
Page 11 and 12: Table 4 480 Volt Ratings - Watts Lo
Page 13 and 14: Table 7 Drive Enclosure Ratings Enc
Page 15 and 16: Figure 2 IP20, NEMA/UL Open Type Fr
Page 17 and 18: Figure 4 NEMA/UL Type 1 Frames 2…
Page 19 and 20: Figure 6 IP00, NEMA/UL Open Type Fr
Page 21 and 22: 1271.0 (50.04) 1221.0 (48.07) 881.8
Page 23 and 24: Figure 10 IP54, NEMA/UL Type 12 Fra
Page 25 and 26: Figure 12 IP54, NEMA/UL Type 12, Fr
Page 27 and 28: 495.5 (19.51) 457.8 (18.02) Figure
Page 29 and 30: 591.50 (23.287) 550.75 (21.683) 465
Page 31 and 32: 875.0 (34.45) 812.0 (31.97) 784.0 (
Page 33 and 34: IP00, NEMA/UL Open Type Frame 6 Lif
Page 35 and 36: Accessing the Terminals Opening the
Page 37 and 38: Step 3 Wire the Drive Special Consi
Page 39 and 40: Voltage Tolerance Nominal Line Nomi
Page 41 and 42: Terminal Block Specifications Table
Page 43 and 44: ➎ ➍ ➌ ➊ ➋ Frame 6 Figure
Page 45 and 46: Common Bus Power Wiring Power Termi
Page 47 and 48: Common Bus Power Terminal Blocks Fr
Page 49 and 50: Using 750-Series Drives with Regen
Page 51 and 52: Table 19 400 Volt AC Input Protecti
Page 53 and 54: Drive Power Jumper Configuration Po
Page 55 and 56: Power Jumper Screw Removal and Stor
Page 57: Figure 34 Frame 7 Jumper Wire Locat
Page 61 and 62: PowerFlex 753 Main Control Board
Page 63 and 64: PowerFlex 755 Main Control Board
Page 65 and 66: Safety Enable Circuitry The drive s
Page 67 and 68: I/O Module 20-750-2262C-2R 20-750-2
Page 69 and 70: I/O Wiring Examples 51 Anlg In0 Hi
Page 71 and 72: Input/Output Connection Example Req
Page 73 and 74: Input/Output Connection Example Req
Page 75 and 76: Safe Torque Off Option Module 20-75
Page 77 and 78: Table 38 Safe Speed Monitor Paramet
Page 79 and 80: I/O Connection Example Encoder Sign
Page 81 and 82: Table 46 Dual Incremental Encoder P
Page 83 and 84: Table 49 Universal Feedback Increme
Page 85 and 86: Auxiliary Power Supply Option Modul
Page 87 and 88: ControlNet Option Module For comple
Page 89 and 90: Step 5 Start-Up Check List Prepare
Page 91 and 92: Navigate to Start-Up Menu Using the
Page 93 and 94: Soft Keys Up to five dynamic soft k
Page 95 and 96: Ports and Devices Drive Device Port
Page 97 and 98: Status Indicators PowerFlex 753 Pow
Page 99 and 100: Event Fault Configuration Auto No.
Page 101 and 102: Event Fault Configuration No. Fault
Page 103 and 104: Event Fault Configuration Auto No.
Page 105 and 106: Common Symptoms and Corrective Acti
Page 107 and 108: Drive (Port 0) Parameter List Numbe
Page 109 and 110:
Number Parameter Name Group 315 SLA
Page 111 and 112:
611 TrmPct RefA AnLo Speed Trim 612
Page 113 and 114:
944 Drive Temp C Status 945 At Limi
Page 115 and 116:
Notes: PowerFlex 750-Series Install
show all

PowerFlex 755 Install Manual.pdf

Create successful ePaper yourself

Delete template?

Save as template?