DM-4800 OWNER'S MANUAL - zZounds.com - Tascam
DM-4800 OWNER'S MANUAL - zZounds.com - Tascam
DM-4800 OWNER'S MANUAL - zZounds.com - Tascam
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
✔<br />
9 – Specifications : Messages and troubleshooting<br />
Action Message Meaning<br />
Confirm LIST Auto Detect?<br />
Press ENTER to confirm,<br />
or a cursor key to cancel.<br />
Confirming the auto-detection of machine control list.<br />
✔ Confirm TRA Auto Detect?<br />
Press ENTER to confirm,<br />
or a cursor key to cancel.<br />
Confirming the auto-detection of transport control mapping.<br />
✔ Copy from Ch2 Automation configuration Confirmation when copying automation configuration.<br />
● Copy Module parameters to CHn. Notification that a parameter copy operation between modules has been carried out<br />
correctly.<br />
✔<br />
✔<br />
✔<br />
Copy Module parameters to CHn?<br />
Press ENTER to confirm,<br />
or a cursor key to cancel.<br />
Copy parameters<br />
within Module?<br />
Press ENTER to confirm<br />
or a cursor key to canvel.<br />
Copy to xxxx fader level<br />
Press ENTER to confirm,<br />
or a cursor key to cancel<br />
Confirmation that parameters are to be copied to another module.<br />
Confirmation when performing a parameter copy operation within the same module.<br />
Confirmation when copying fader levels. xxxx may be ALL, ALL MASTER, Aux 1-8, groups<br />
of 8 busses, or groups of 8 channels.<br />
● Copy was <strong>com</strong>pleted. Popup message on <strong>com</strong>pletion of copy operation.<br />
● Copying project.<br />
Do not remove the CF card.<br />
Shown while a project is being copied on the CF card.<br />
✔ Create project?<br />
Press ENTER to confirm,<br />
or a cursor key to cancel.<br />
Confirming creation of a project.<br />
● Creating project.<br />
Do not remove the CF card.<br />
Warning not to remove CF card during project <strong>com</strong>pletion.<br />
✖ Current Data initialized.<br />
Notice to restart the <strong>DM</strong>-<strong>4800</strong> following a change of reinitialization and sampling<br />
Fs has changed.<br />
Mixer will reboot.<br />
Press ENTER to confirm,<br />
or a cursor key to cancel.<br />
frequency.<br />
Current project is protected.<br />
An attempt has been made to shut down the <strong>DM</strong>-<strong>4800</strong> while the current project’s<br />
✔ Can't STORE current project.<br />
ENTER key : Shut down<br />
CURSOR key : Cancel<br />
version on card is protected (meaning that it cannot be saved).<br />
● Data change was applied. Date and time have been changed.<br />
● Data has not been changed. Date and time have not been changed.<br />
● Deleting project.<br />
Do not remove the CF card.<br />
Shown while a project is being deleted from the CF card.<br />
✖ Device is not active. A device selected for transport control is not active.<br />
✖ Digital In1: Error<br />
Not audio signal<br />
Press ENTER to continue.<br />
The DIGITAL IN audio source is not providing digital audio data.<br />
✖ Digital In1: Error<br />
The DIGITAL IN clock source is not providing digital audio data, and the sync clock is now<br />
Not audio signal<br />
Source Fs unlocked<br />
Press ENTER to continue.<br />
unlocked.<br />
✖ Digital In1: Error<br />
The DIGITAL IN clock source has experienced an error, and the sync clock is now<br />
Source Fs unlocked<br />
Press ENTER to continue.<br />
unlocked.<br />
Table 9.1: Popup messages (continued)<br />
TASCAM <strong>DM</strong>-<strong>4800</strong> User’s Manual 127
Change language