The System Manual of SOL-20 - History of Computers

More documents

Recommendations

Info

PROCESSOR TECHNOLOGY CORPORATION Sol POWER SUPPLY SECTION II Table 2-2. Sol-10 Power Supply Parts List. The Sol-10 Power Supply Kit includes all Sol-REG parts listed in Table 2-l plus the following components: .__-_--------------------------------------------------------------. 1 *Power Transformer, T1 1 *Fuse, 3 amp Slo-Blo (F1) *Chassis-mounted component Table 2-3. Sol-20 Power Supply Parts List. The Sol-20 Power Supply Kit includes all Sol-REG parts listed in Table 2-l plus the following components: ,------------------_--------------------------------------------- RESISTORS 1 *39 ohm, 2 watt, 5% CAPACITORS 1 *54,000 ufd, electrolytic RECTIFIERS 1 *MDA980-1 (FWB3) TRANSFORMERS 1 *Power Transformer, T2 MISCELLANEOUS 1 *Fan 1 *Fan Guard 1 *Fuse, 3 amp Slo-Blo 1 5-wire Cable Assembly 1 *Clamp for C9, 21/2" 2 *#l0 solder lug, internal tooth *Chassis-mounted component II-4
PROCESSOR TECHNOLOGY CORPORATION Sol POWER SUPPLY SECTION II 2.3 ASSEMBLY TIPS 2.3.1 Electrical For the most part the assembly tips given in Paragraph 3.2 of Section III (Page III-l) apply to assembling the Sol regulator board and power supply. In addition, scan Section II completely before you start to assemble the power supply. 2.3.2 Mechanical 1. If you do not have the proper screwdrivers (see Paragraph 2.5), we recommend that you buy them rather than using a knife point, a blade screwdriver on a Phillips screw, and other makeshift means. Proper screwdrivers minimize the chances of stripping threads, disfiguring screw heads and marring decorative surfaces. 2. To assure a correct fit and tight assembly, be sure you use the screws specified in the instructions. 3. Lockwashers are widely used in the power supply assembly so that screws will not loosen when subjected to stress or vibration. When a lockwasher is specified, do not omit it and make sure you install it correctly. 4. Some instructions call for prethreading holes. This is done to make assembly easier by giving you maximum working space for installing relatively hard-to-drive sheet metal screws. If you bypass prethreading instructions you will only make subsequent cabinet-chassis assembly more difficult. To prethread a hole, insert specified screw in the hole and position it as straight as possible. While holding the screw in this position, drive it into the metal with the proper screwdriver. If started straight the screw will continue to go straight into the metal so that the head and sheet metal surfaces are in full contact. 5. The diameter of the shank (threaded portion) of a screw increases in relation to its number. For example, a 6-32 screw is larger in diameter than a 4-40 screw. Also, a #8 lockwasher is larger than a #4 lockwasher. 6. Heat sink compound is supplied with this kit in a small clear plastic package. It is a thick white substance which improves transfer between components and their heat sinks. To use the compound, pierce a small hole near the edge of the top surface of the plastic package, using a pin or sharp knife point. Squeezing the package will cause a small amount of the compound to ooze out Rev B II-5
Page 1 and 2: Sol SYSTEMS MANUAL, 6200 Hollis Str
Page 3 and 4: CONTENTS OUTILNE Detailed contents
Page 5 and 6: Sol TERMINAL COMPUTERTM FIGURE 7-5
Page 7 and 8: PROCESSOR TECHNOLOGY CORPORATION So
Page 13: PROCESSOR TECHNOLOGY CORPORATION So
Page 33 and 34: PROCESSOR TECHNOLOGY CORPORATION TM
Page 64 and 65:
PROCESSOR TECHNOLOGY CORPORATION So
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
PROCESSOR TECHNOLOGY CORPORATION Sa
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
PROCESSOR TECHNOLOGY CORPORATION Sa
Page 86 and 87:
Page 88:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
VIII THEORY OF OPERATION 8.1 INTROD
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 187 and 188:
SECTION IX SOFTWARE Sol TERMINAL CO
Page 189 and 190:
Page 192 and 193:
M0100 SOLOS (tm) /CUTER (tm) USER'S
Page 194 and 195:
P R E F A C E This manual describes
Page 196:
TABLE OF CONTENTS (cont.) IV. SET C
Page 199 and 200:
INTRODUCTION (cont.) Only the first
Page 201 and 202:
II. CONSOLE COMMANDS Console Comman
Page 203 and 204:
III. TAPE COMMANDS Tape commands ar
Page 205 and 206:
III. TAPE COMMANDS (cont.) Note: A
Page 207 and 208:
V. SET COMMANDS (cont.) The Output
Page 209 and 210:
V. SET COMMANDS (cont.) The Custom
Page 211 and 212:
V. SUBROUTINES A. Introduction to t
Page 213 and 214:
V. SUBROUTINES (cont.) JUMP TABLE A
Page 215 and 216:
V. SUBROUTINES (cont.) AOUT entry p
Page 217 and 218:
V. SUBROUTINES (cont.) When calling
Page 219 and 220:
V. SUBROUTINES (cont.) SOLOS provid
Page 221 and 222:
VI. LOADING & EXECUTING CUTER (Appl
show all

The System Manual of SOL-20 - History of Computers

Create successful ePaper yourself

Delete template?

Save as template?