Series 360, Granville-Phillips, Stabil-Ion, Ionization, Vacuum ...

More documents

Recommendations

Info

1 System Components Figure 1-8 Top View of Stabil-Ion Vacuum Gauge Control Unit (Cover and Door Removed). 1-6 Series 360 Stabil-Ion December, 2001
Chapter 2 2 Initial Setup Procedures 2.1 Control Unit Setup 1. Open the front panel door and determine if any of the following options are installed: ■ Process Control ■ RS232 Computer Interface ■ IEEE 488 Computer Interface RS-232 ELECTROMETER CONVECTRON IG-1 AUTO PROCESS CONTROL Off SP On Data Port IG2 Scale IG1 Factor Adjust Pressure Range L HL H Cathode 1 21 2 IG1 IG2 OFF SET ATM VAC IG-2 AUTO OFF SET ATM VAC 1 2 3 4 5 6 3 ▲ Set ▲ C H A N N E L IG1 O Degas O IG2 O On O Remote Figure 2-1 Control Unit Front Panel (with Door Open) Showing Location of Computer Interface and Process Control Modules. 2. If none of the above options are present and if the pressure display units of measure are correct (See Figure 2-2.), and you do not wish to change the degas power timer from the factory setting of 10 minutes, skip to Chapter 3 Installation. 3. If one or more of the above options is present, or if you wish to change the units of measure or degas time setting, you may find it necessary to reconfigure certain switches within the Control Unit. IG 2.13 -8 A B 5.67 -2 745 1 2 3 4 5 6 TORR IG1 O IG2 O DEGAS ON O O Figure 2-2 Control Unit Front Panel Showing Location of Units of Measure Label. Review Sections 2.1.3, 2.1.4, 2.1.5, 2.1.6, and 2.1.7 for the factory default settings for the switches on these options, the pressure display units of measure, and the degas power timer to determine if any need changing. Now is a convenient time to make any required switch changes before mounting the Control Unit in its desired location. Series 360 Stabil-Ion December, 2001 2-1
Page 1 and 2: Series 360 1Granville-Phillips Stab
Page 3 and 4: Table of Contents Safety. . . . . .
Page 5 and 6: Safety Safety Safety Instructions S
Page 7 and 8: Safety Proper Grounding: All compon
Page 9 and 10: Safety Certification Helix Technolo
Page 11 and 12: Chapter 1 1 System Components 1 5 8
Page 13 and 14: 1 System Components 23 22 21 20 19
Page 15: 1 System Components 10 9 8 POWER 50
Page 19 and 20: 2 Initial Setup Procedures 2.1.2 Pr
Page 21 and 22: 2 Initial Setup Procedures 2.1.4 Pr
Page 23 and 24: 2 Initial Setup Procedures 2.1.4.1
Page 27 and 28: 2 Initial Setup Procedures 2.1.5.1.
Page 31 and 32: 2 Initial Setup Procedures 2.2 Powe
Page 33 and 34: Chapter 3 3 Installation It is the
Page 35 and 36: 3 Installation ■ ■ ■ Avoid co
Page 37 and 38: 3 Installation 3.4 Installing the C
Page 39 and 40: 3 Installation 3.5 Connecting Analo
Page 41 and 42: 3 Installation 1. Using Table 3-1 a
Page 43 and 44: 3 Installation Table 3-2 Connection
Page 45 and 46: 3 Installation 3.7.3 Using the Remo
Page 47 and 48: 3 Installation RTS Negated by 360 o
Page 49 and 50: 3 Installation 3. Connect the Stabi
Page 51 and 52: 3 Installation 3.11 Connecting the
Page 53 and 54: Chapter 4 4 Preparing the Stabil-Io
Page 55 and 56: 4 Preparing the Stabil-Ion System f
Page 67 and 68:
4 Preparing the Stabil-Ion System f
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Chapter 5 5 Operation of a Stabil-I
Page 89 and 90:
Chapter 6 6 Service and Maintenance
Page 91 and 92:
6 Service and Maintenance Symptom I
Page 93 and 94:
6 Service and Maintenance 6.4 Overp
Page 95 and 96:
6 Service and Maintenance 6.7 Troub
Page 97 and 98:
6 Service and Maintenance 6.10 Proc
Page 99 and 100:
6 Service and Maintenance 9. Carefu
Page 101 and 102:
6 Service and Maintenance CONVECTRO
Page 103 and 104:
Index A AC line voltage Between 180
show all

Series 360, Granville-Phillips, Stabil-Ion, Ionization, Vacuum ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?