16.03.2014 Views

GR-DVL9600 GR-DVL9500 - JVC

GR-DVL9600 GR-DVL9500 - JVC

GR-DVL9600 GR-DVL9500 - JVC

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION<br />

29. During recording, the date/<br />

time does not appear.<br />

29. • “DISPLAY” is set to “OFF” in the<br />

Date/Time Menu.<br />

• Interface shooting is performed.<br />

EN69<br />

29. • Set “DISPLAY” to “ON” in the<br />

Date/Time Menu ( pg. 20).<br />

• During interface shooting, the<br />

date/time does not appear<br />

( pg. 17).<br />

• Press IND. ON/OFF for longer<br />

than 1 second to make the<br />

indicators appear ( pg. 15).<br />

30. The indicators and messages<br />

do not appear.<br />

31. Images on the LCD monitor<br />

appear dark or whitish.<br />

32. The rear of the LCD monitor is<br />

hot.<br />

30. • “ON SCREEN” is set to “OFF” in<br />

the Date/Time Menu.<br />

• You have made the indicators<br />

disappear.<br />

31. • In places subject to low<br />

temperature, images become<br />

dark due to the characteristics of<br />

the LCD monitor. When this<br />

happens, the displayed colours<br />

differ from those that are<br />

actually recorded. This is not a<br />

defect of the camcorder.<br />

• When the LCD monitor’s<br />

fluorescent light reaches the end<br />

of its service life, images on the<br />

LCD monitor become dark.<br />

Consult your nearest <strong>JVC</strong> dealer.<br />

32. • The light used to illuminate the<br />

LCD monitor causes it to<br />

become hot.<br />

30. • Set “ON SCREEN” to “ON” in<br />

the Date/Time Menu ( pg. 20).<br />

• Press IND. ON/OFF for longer<br />

than 1 second to make the<br />

indicators appear ( pg. 15).<br />

31. • Adjust the brightness and angle<br />

of the LCD monitor ( pg. 17).<br />

32. • Close the LCD monitor to turn it<br />

off or set the Power Switch to<br />

“OFF”, and let the unit cool<br />

down.<br />

33. The indicators and the image<br />

colour on the LCD monitor are<br />

not clear.<br />

33. • This may occur when the<br />

surface or the edge of the LCD<br />

monitor is pressed.<br />

33.<br />

————<br />

34. The LCD monitor or<br />

viewfinder indications blink.<br />

34. • Certain Fade/Wipe effects,<br />

certain modes of Programme AE<br />

with special effects, “DIS” and<br />

other functions that cannot be<br />

used together are selected at the<br />

same time.<br />

34. • Re-read the sections covering<br />

Fade/Wipe effects, Programme<br />

AE with special effects and<br />

“DIS” ( pg. 29, 31–35).<br />

35. Coloured bright spots appear<br />

all over the LCD monitor or<br />

the viewfinder.<br />

35. • The LCD monitor or the<br />

viewfinder is made with highprecision<br />

technology. However,<br />

black spots or bright spots of<br />

light (red, green or blue) may<br />

appear constantly on the LCD<br />

monitor or the viewfinder. These<br />

spots are not recorded on the<br />

tape. This is not due to any<br />

defect of the unit. (Effective<br />

dots: more than 99.99 %)<br />

35.<br />

————<br />

36. During recording, sound<br />

cannot be heard.<br />

36. • The optional headphones are<br />

not connected to the headphones<br />

connector.<br />

• The sound volume of the<br />

headphones connector was not<br />

adjusted appropriately. The<br />

sound volume at this point is the<br />

same as the level it was adjusted<br />

to during playback.<br />

36. • Connect the optional headphones<br />

to the headphones<br />

connector ( pg. 64).<br />

• Adjust the sound volume during<br />

playback ( pg. 43).<br />

CONTINUED ON NEXT PAGE

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!