GR-DVL9600 GR-DVL9500 - JVC
GR-DVL9600 GR-DVL9500 - JVC
GR-DVL9600 GR-DVL9500 - JVC
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
70 EN TROUBLESHOOTING (cont.)<br />
SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION<br />
37. Play, Rewind and Fast-Forward<br />
functions do not work.<br />
37. • The Power Switch is not set to<br />
“ ”.<br />
37. • Set the Power Switch to “ ”<br />
( pg. 43).<br />
38. The tape is moving, but there<br />
is no picture.<br />
39. The LCD monitor indications<br />
are distorted.<br />
40. Images on the LCD monitor<br />
are jittery.<br />
38. • Your TV has AV input terminals,<br />
but is not set to its VIDEO mode.<br />
• The cassette’s cover is open.<br />
39. • During playback of the<br />
unrecorded portion, High-speed<br />
Search and still playback, LCD<br />
monitor indications appear<br />
distorted. This is not a defect.<br />
40. • The speaker volume is too great.<br />
38. • Set the TV to the mode or<br />
channel appropriate for video<br />
playback ( pg. 48, 49).<br />
• Close the cassette's cover<br />
( pg. 9).<br />
39.<br />
————<br />
40. • Turn the speaker volume down<br />
( pg. 43).<br />
41. The LCD monitor, the<br />
viewfinder and the lens have<br />
become dirty<br />
(ex. fingerprints).<br />
41.<br />
————<br />
41. • Wipe them gently with soft<br />
cloth. Wiping strongly can<br />
cause damage.<br />
42. An unusual mark appears.<br />
43. An error indication<br />
(E01 — E06) appears.<br />
44. The charger indicator on the<br />
AC Power Adapter/Charger<br />
does not light.<br />
42.<br />
————<br />
43. • A malfunction of some kind has<br />
occurred. In this case the<br />
camcorder’s functions become<br />
unusable.<br />
44. • The temperature of the battery is<br />
extremely high/low.<br />
• Charging is difficult in places<br />
subject to extremely high/low<br />
temperatures.<br />
42. • Check the section of the manual<br />
that explains LCD monitor/<br />
viewfinder indications<br />
( pg. 74, 75).<br />
43. • Remove the power supply<br />
(battery pack, etc.) and wait a<br />
few minutes for the indication to<br />
clear. When it does, you can<br />
resume using the camcorder.<br />
If the indication remains even<br />
though you repeat the above<br />
two or three times, please<br />
consult your nearest <strong>JVC</strong> dealer.<br />
44. • To protect the battery, it is<br />
recommended to charge it in<br />
places with a temperature of<br />
10°C to 35°C ( pg. 77).<br />
45. The recording mode indicator<br />
“LP” blinks.<br />
45. • This occurs when recording in<br />
the LP mode is not available.<br />
After the indicator blinks, the<br />
recording mode switches to<br />
“SP” and recording goes on.<br />
45.<br />
————<br />
46. Picture does not appear on the<br />
LCD monitor.<br />
47. When the image is printed<br />
from the printer, a black bar<br />
appears at the bottom of the<br />
screen.<br />
48. The power lamp blinks.<br />
46 • The viewfinder is pulled out.<br />
• The LCD monitor's brightness<br />
setting is too dark.<br />
47. • This is not a malfunction.<br />
48. • The camcorder was turned on<br />
when the battery power was<br />
almost gone.<br />
46. • Push the viewfinder back in.<br />
• Adjust the brightness of the LCD<br />
monitor ( pg. 17).<br />
• If the monitor is tilted upward<br />
180 degrees, open the monitor<br />
fully ( pg. 23).<br />
47. • By recording with “DIS”<br />
activated ( pg. 29) this can be<br />
avoided.<br />
48. • Replace with a charged battery<br />
pack ( pg. 6, 7).