SunTouch® - Pentair

More documents

Recommendations

Info

50 Grounding and Bonding to the SunTouch Power Center Connect a ground wire from the primary electrical panel to the SunTouch ground bus bar. Also ground each piece of high voltage (120 VAC or 240 VAC) equipment that is connected to the SunTouch Power Center relays. The SunTouch Power Center must also be connected to the pool bonding system using an 8 AWG (minimum) wire. An earth terminal for bonding is provided on the grounding bus bar inside the Power Center. For input AC wiring information, see page 520. Grounding Bus Bar (three terminals for relays and one for main AC ground wire) SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
51 Preparing the SunTouch Power Center Before mounting the SunTouch Power Center, first open the front door and the front panel to access the conduit knockouts and low voltage raceway. Opening the front panel To access the SunTouch Power Center electronics compartment: 1. Unlatch the front door, 2. Loosen the retaining screw on front panel. Open the hinged front panel to access the electronics compartment. 3. Proceed with: • Mounting the SunTouch Power Center, page 51 • Removing Electrical Conduit Knockouts, page 53 • Installing Conduit and Wire to the SunTouch Power Center, page 54 • Transformer Connections, page 55 • SunTouch Motherboard Connections, page 56 4. After all electrical connections have be completed, close the front panel and secure it with the retaining screw. Front panel Front panel retaining screw SunTouch Power Center (Shared Equipment System) SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
Page 1 and 2:
SunTouch ® Pool, Spa and Solar Con
Page 3 and 4:
i Contents IMPORTANT WARNING AND SA
Page 5 and 6:
iii Contents Installing Valve Actua
Page 7 and 8: v IMPORTANT WARNING AND SAFETY INST
Page 9 and 10: 1 SunTouch ® Control System Overvi
Page 11 and 12: 3 Control Buttons (Continued) ➂
Page 13 and 14: 5 Operating SunTouch in Solar Only
Page 15 and 16: 7 Solar Only Menus (Continued) Syst
Page 17 and 18: 9 Freeze Protection in Solar Only m
Page 19 and 20: 11 SunTouch Main Status Screen (Poo
Page 21 and 22: 13 Pool/Spa Mode Menus The followin
Page 23 and 24: 15 Heat Menu (2/14) (Continued) Spa
Page 25 and 26: 17 Schedules Menu (4/14) Scheduled
Page 27 and 28: 19 Clock Menu (5/14) Use the Clock
Page 29 and 30: 21 Valves Menu (7/14) The valves fe
Page 31 and 32: 23 Advanced Menu (8/14): Calibrate
Page 33 and 34: 25 Advanced Menu (8/14): Reset Fact
Page 35 and 36: 27 SunTouch Solar, Pool and Spa Con
Page 37 and 38: 29 To select a single-speed pump. M
Page 39 and 40: 31 Pump Menu (12/14) (Continued) In
Page 45 and 46: 37 IntelliChlor Menu (13/14): Statu
Page 47 and 48: 39 SunTouch Main Status Screen (Poo
Page 49 and 50: 41 Pool/Spa Mode (Single Body of Wa
Page 51 and 52: 43 SunTouch Solar Package Contents
Page 53 and 54: 45 SunTouch Power Center (Front Vie
Page 55 and 56: 47 8 9 Plumb the solar feed and ret
Page 57: 49 SunTouch Power Center High Volta
Page 61 and 62: 53 Removing Electrical Conduit Knoc
Page 63 and 64: 55 Transformer Connections High Vol
Page 65 and 66: 57 Accessing the SunTouch Motherboa
Page 67 and 68: 59 Installing relays (Continued) St
Page 69 and 70: 61 Installing and Connecting Temper
Page 71 and 72: 63 Connecting to a Sta-Rite ® Gas
Page 73 and 74: 65 SunTouch Pool/Spa Controller Sys
Page 75 and 76: 67 Connecting IntelliChem to the Su
Page 77 and 78: 69 SunTouch Error Messages Error Me
Page 79 and 80: 71 Temperature vs. Resistance Data
Page 81 and 82: 73 SunTouch Solar, Pool and Spa Con
Page 83 and 84: 75 Wiring SunTouch to the IntelliCh
Page 85 and 86: 77 Wiring IntellilChlor (SCG) and I
Page 87 and 88: 79 Installing the ESO Circuit Board
Page 89 and 90: 81 Commercial Application using ESO
Page 91 and 92: How to BACKWASH Your Filter When yo
show all

SunTouch® - Pentair

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?