SunTouch® - Pentair

More documents

Recommendations

Info

64 SunTouch Solar System Installation • To ensure maximum flow of water through the solar panels, a solar booster pump should be added if panels are installed at a very high elevation. • It is recommended that the solar panels are mounted in a way that gravity will allow draining whenever the filter pump is not on. • For systems with glazed panels, damage can occur from overheating if the filter pump is still running after the solar has turned off. To enable glazed panels to automatically drain whenever the solar turns off (even if the filter pump is still running), a 1/2" motorized solar drain valve should be plumbed from the solar feed line, through a check valve, to a zero psi point (such as pool fill line or jet air intake). SunTouch Solar System Start-Up 1. Switch power on to the SunTouch Power Center. 2. If pool cleaner protection has been added to the system, the pool cleaner pump motor should be activated whenever the pool cleaner timer is on. Momentarily turn pool cleaner on and off to check the motor is operating correctly. 3. Check that Solar Valve is in “solar bypass” position, diverting water away from solar panels. If Solar Valve is staged incorrectly (diverting water to the solar panels), reverse switch on back of Valve Actuator (change from ON1 to ON2, or vice-versa). The Valve Actuator will automatically rotate to the correct position. 4. Check that Solar Valve has rotated from the “solar bypass” position to the “solar” position, diverting water through the solar panels. 5. The system is now ready to be operated as desired. Pool Cleaner Protection Recommended for use in pool systems which utilize a “booster pump” pool cleaner. This feature automatically turns off the pool cleaner pump for a few minutes whenever solar is initiated. This will protect the pump from damage caused by air in the solar panels at system start-up. SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
65 SunTouch Pool/Spa Controller System Start-Up Perform the following start-up procedures to ensure that the SunTouch enclosure is installed correctly. Before you power up the SunTouch enclosure check the following: Check Electronics Check that the following plugs are seated correctly on the motherboard: • Relay connectors - PUMP - AUX1 - AUX2 • Temperature sensors connectors WATER, SOLAR, AIR (J9) • Transformer wire harness (J10) attached to the motherboard. • Heater control connector GAS HEATER (J12) or two-wire screw terminal. Refer to "Summary System Installation Steps Summary," on page 37, and "SunTouch Motherboard Connections on page 51. SunTouch System Test The following describes how to test the main control panel to activate the heater, valves and pumps. Before testing the system, be sure that all pool and spa equipment has been properly installed and connected to the SunTouch enclosure. Testing Valve Actuators and Filter Pump Use the following steps to test the valve actuators (CVA24T - P/N 263045) for proper rotation. To test the valve actuators and pool/spa filter pump: 1. Power up the SunTouch Power center. 2. Press the MENU button. Circuit On/Off is displayed. Press the Right arrow button access the pool filter pump circuit. Press the Up or Down arrow button and select ON. Press the Left arrow button to return to the main status screen. POOL and the temperature setting will be displayed as shown below. 3. The pool filter pump should be operating. Water will be removed from the pool and returned to the pool. POOL 71°F / 91°F 11: 51AM HEATER Testing the auxiliary relays To verify that AUX 1, AUX 2 and AUX 3 relays outputs are operating correctly: 1. Power up the SunTouch Power center. 2. Press the MENU button. Circuit On/Off is displayed. Press the Right arrow button access the AUX 1 setting. Press the Up or Down arrow button and select ON. Press the Left arrow button to return to the main status screen. The auxiliary number will be displayed as shown below. 3. Repeat step 2 to test AUX 2 and AUX 3 relay. AIR 71°F 11: 51AM AUX123 SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
Page 1 and 2:
SunTouch ® Pool, Spa and Solar Con
Page 3 and 4:
i Contents IMPORTANT WARNING AND SA
Page 5 and 6:
iii Contents Installing Valve Actua
Page 7 and 8:
v IMPORTANT WARNING AND SAFETY INST
Page 9 and 10:
1 SunTouch ® Control System Overvi
Page 11 and 12:
3 Control Buttons (Continued) ➂
Page 13 and 14:
5 Operating SunTouch in Solar Only
Page 15 and 16:
7 Solar Only Menus (Continued) Syst
Page 17 and 18:
9 Freeze Protection in Solar Only m
Page 19 and 20:
11 SunTouch Main Status Screen (Poo
Page 21 and 22: 13 Pool/Spa Mode Menus The followin
Page 23 and 24: 15 Heat Menu (2/14) (Continued) Spa
Page 25 and 26: 17 Schedules Menu (4/14) Scheduled
Page 27 and 28: 19 Clock Menu (5/14) Use the Clock
Page 29 and 30: 21 Valves Menu (7/14) The valves fe
Page 31 and 32: 23 Advanced Menu (8/14): Calibrate
Page 33 and 34: 25 Advanced Menu (8/14): Reset Fact
Page 35 and 36: 27 SunTouch Solar, Pool and Spa Con
Page 37 and 38: 29 To select a single-speed pump. M
Page 39 and 40: 31 Pump Menu (12/14) (Continued) In
Page 45 and 46: 37 IntelliChlor Menu (13/14): Statu
Page 47 and 48: 39 SunTouch Main Status Screen (Poo
Page 49 and 50: 41 Pool/Spa Mode (Single Body of Wa
Page 51 and 52: 43 SunTouch Solar Package Contents
Page 53 and 54: 45 SunTouch Power Center (Front Vie
Page 55 and 56: 47 8 9 Plumb the solar feed and ret
Page 57 and 58: 49 SunTouch Power Center High Volta
Page 59 and 60: 51 Preparing the SunTouch Power Cen
Page 61 and 62: 53 Removing Electrical Conduit Knoc
Page 63 and 64: 55 Transformer Connections High Vol
Page 65 and 66: 57 Accessing the SunTouch Motherboa
Page 67 and 68: 59 Installing relays (Continued) St
Page 69 and 70: 61 Installing and Connecting Temper
Page 71: 63 Connecting to a Sta-Rite ® Gas
Page 75 and 76: 67 Connecting IntelliChem to the Su
Page 77 and 78: 69 SunTouch Error Messages Error Me
Page 79 and 80: 71 Temperature vs. Resistance Data
Page 81 and 82: 73 SunTouch Solar, Pool and Spa Con
Page 83 and 84: 75 Wiring SunTouch to the IntelliCh
Page 85 and 86: 77 Wiring IntellilChlor (SCG) and I
Page 87 and 88: 79 Installing the ESO Circuit Board
Page 89 and 90: 81 Commercial Application using ESO
Page 91 and 92: How to BACKWASH Your Filter When yo
show all

SunTouch® - Pentair

Create successful ePaper yourself

Delete template?

Save as template?