SunTouch® - Pentair

More documents

Recommendations

Info

80 Installing the ESO Circuit Board (Continued) 6. Connecting the ESO switch: Route a two-wire cable through grommet located on the left-side of the SunTouch Power Center, up into the low voltage raceway to the ESO switch circuit board. 7. Connect the two wires to J13 on the ESO switch circuit board. Connect the other end of the cable to the emergency switch as shown below. 8. Verify that all cable connections are connected correctly. Close the front panel and secure it with the retaining screw. The Emergency Shut-Off Switch installation is complete. Emergency shut-off circuit board A A B B C C D E F J13 SHUT OFF + - D E F Grommet (Low voltage raceway) 2-wire connection SunTouch Power Center Emergency Shut-Off switch (ESO) SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
81 Commercial Application using ESO3 and SunTouch (Single Body System) Using a Emergency Shut-Off Switch (ESO3), circuit board, and a spring wound timer switch (Intermatic ® or equivalent), a SunTouch single body system (P/N 520859) can be configured for a commercial application. A typical configuration, using a single speed pump is shown in the “Commercial Application Connection Diagram” below. As shown, the commercial spa jet pump is controlled by the spring wound timer switch and AUX 1 (Jet pump) is programmed by SunTouch to operate from 5:00 AM to 12:00 AM. When the Emergency Shut-Off Switch is pressed, both relays will disengage. If the pool or spa light is controlled by AUX 2, the light will remain operational. SunTouch for commercial appliction with IntelliFlo VS+SVRS and IntelliFlo VSF+SVRS pump IntelliFlo VS+SVRS and VSF+SVRS filter pump is controller by SunTouch Internal time clock AUX 1 (VS+SVRS Jet Pump) in this applicatin will be programmed to operate during the hours of operation (e.g. 5:00 AM - 12:00 AM). When Emergency Switch is pressed, both relays disengaged. If the pool or spa light are controlled by AUX 2 light will remain on. For use with single speed pumps or IF VS+SVRS. CR2032 +3V GAS HEATER J12 RESET SunTouch Motherboard P/N 520859 Pool or Spa Light INTAKE RETURN SOLAR PUMP AUX 1 AUX 2 AUX 3 VLV A VLV B VLV C VALVE ACTUATORS SOLAR ONLY CLNR ESO Emergency Shut Off Switch IntelliFlo VS+SVRS /VSF-SVRS Jet Pump Relay F J13 F LINE VOLTAGE E E Note: Spring wound timer must be a DPST switch. Both legs of power must be turned OFF. For IntelliFlo VS+SVRS/VSF+SVRS, disable “Priming” feature. AUX (Filter Pump) AUX 1 AUX 2 (POOL or SPA Light) + - D SHUT OFF D C C B ESO Module LINE VOLTAGE B A A 520106 520106 Required Parts: 1. P/N 520859 SunTouch Single Body 2. P/N ES03 Emergency Shut Off 3. Spring Timer (P/N FF4 15M, FF4 30M, FF4 60M) Note: Spring wound timer (DPS) for booster jet pump must be rated for proper amperage. IntelliFlo VS+SVRS /VSF-SVRS Filter Pump Relay LINE VOLTAGE LINE VOLTAGE Commercial Spa Jet Pump (For IntelliFlo VS+SVRS/VSF+SVRS, disable PRIMING feature) Spring Wound Timer Switch (DPST) WhisperFlo® Filter Pump (or IntelliFlo VS-SVRS/VSF-SVRS) SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
Page 1 and 2:
SunTouch ® Pool, Spa and Solar Con
Page 3 and 4:
i Contents IMPORTANT WARNING AND SA
Page 5 and 6:
iii Contents Installing Valve Actua
Page 7 and 8:
v IMPORTANT WARNING AND SAFETY INST
Page 9 and 10:
1 SunTouch ® Control System Overvi
Page 11 and 12:
3 Control Buttons (Continued) ➂
Page 13 and 14:
5 Operating SunTouch in Solar Only
Page 15 and 16:
7 Solar Only Menus (Continued) Syst
Page 17 and 18:
9 Freeze Protection in Solar Only m
Page 19 and 20:
11 SunTouch Main Status Screen (Poo
Page 21 and 22:
13 Pool/Spa Mode Menus The followin
Page 23 and 24:
15 Heat Menu (2/14) (Continued) Spa
Page 25 and 26:
17 Schedules Menu (4/14) Scheduled
Page 27 and 28:
19 Clock Menu (5/14) Use the Clock
Page 29 and 30:
21 Valves Menu (7/14) The valves fe
Page 31 and 32:
23 Advanced Menu (8/14): Calibrate
Page 33 and 34:
25 Advanced Menu (8/14): Reset Fact
Page 35 and 36:
27 SunTouch Solar, Pool and Spa Con
Page 37 and 38: 29 To select a single-speed pump. M
Page 39 and 40: 31 Pump Menu (12/14) (Continued) In
Page 45 and 46: 37 IntelliChlor Menu (13/14): Statu
Page 47 and 48: 39 SunTouch Main Status Screen (Poo
Page 49 and 50: 41 Pool/Spa Mode (Single Body of Wa
Page 51 and 52: 43 SunTouch Solar Package Contents
Page 53 and 54: 45 SunTouch Power Center (Front Vie
Page 55 and 56: 47 8 9 Plumb the solar feed and ret
Page 57 and 58: 49 SunTouch Power Center High Volta
Page 59 and 60: 51 Preparing the SunTouch Power Cen
Page 61 and 62: 53 Removing Electrical Conduit Knoc
Page 63 and 64: 55 Transformer Connections High Vol
Page 65 and 66: 57 Accessing the SunTouch Motherboa
Page 67 and 68: 59 Installing relays (Continued) St
Page 69 and 70: 61 Installing and Connecting Temper
Page 71 and 72: 63 Connecting to a Sta-Rite ® Gas
Page 73 and 74: 65 SunTouch Pool/Spa Controller Sys
Page 75 and 76: 67 Connecting IntelliChem to the Su
Page 77 and 78: 69 SunTouch Error Messages Error Me
Page 79 and 80: 71 Temperature vs. Resistance Data
Page 81 and 82: 73 SunTouch Solar, Pool and Spa Con
Page 83 and 84: 75 Wiring SunTouch to the IntelliCh
Page 85 and 86: 77 Wiring IntellilChlor (SCG) and I
Page 87: 79 Installing the ESO Circuit Board
Page 91 and 92: How to BACKWASH Your Filter When yo
show all

SunTouch® - Pentair

Create successful ePaper yourself

Delete template?

Save as template?