SunTouch® - Pentair

More documents

Recommendations

Info

68 Section 3 Troubleshooting Troubleshooting Use the following troubleshooting information to help resolve problems that may occur when using the SunTouch system. If by following the recommended actions you are still unable to resolve the problems, please contact Technical Support (see page vi). Frequently Asked Questions (FAQ) How do I setup a two-speed pump? A two-speed pump operates using two relays and one or more circuits. The first relay turns the pump on or off. Assuming this is a filter pump, this circuit is controlled by the pool and spa circuits or any other circuit that may be tied to the filter pump (such as circuits with freeze protection, etc.). The second relay (AUX 2) switches the pump from low speed to high speed. The default condition is low speed. Up to three circuits may be assigned to trigger the pump to high speed. However, if three relays are being used, two relays must be located outside the SunTouch enclosure. The SunTouch enclosure which houses two relays. Note: These circuits do not switch the pump on. To configure a two-speed pump relay, refer to “Settings Menu: 2-Speed Pump,” on page 29. For relay location and wiring (see page 53). The 2-Speed pump relay connector is plugged into the AUX 3 output socket on the SunTouch motherboard. Can I switch the heater on and change the temperature from the spa? The heater may be switched on from the spa location using the QuickTouch wireless remote controller (optional), see page 28 for setup details. How do I switch on solar heating? The system must first be configured for solar heating. Go to the “Heat” menu (see page 14) and enable “Solar” as the heat source. Note: Do not select “Heat Pump” as the solar heating method. SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
69 SunTouch Error Messages Error Messages If the system detects that a sensor is not connected to the SunTouch Power Center or it is defective, an error message is displayed in the Diagnostics menu (page 25). The following lists the sensor errors. Error Message Air Err (Displays on the Main Screen) Air Temperature Err (Displays in the "Diagnostics" menu) Water Temperature Err (Displays in the "Diagnostics" menu) Solar Temperature Err (Displays in the "Diagnostics" menu) Possible Cause Air sensor not connected to the SunTouch motherboard. Air sensor not connected to the SunTouch motherboard. Water sensor not connected to the SunTouch motherboard. Solar sensor not connected to the SunTouch motherboard. Solution Check that the air sensor plug is connected to J21 connector on the motherboard. Check that the sensor wire is connected properly. Check that the air sensor plug is connected to J21 connector on the motherboard. Check that the water sensor plug is connected to J21 connector on the motherboard. Check that the solar sensor plug is connected to J21 connector on the motherboard. Self Test Error Codes The “Self Test” feature is intended for use by service personnel. If after performing a control panel self test (see Diagnostics menu page 25) there were no errors detected, Code 0 is displayed, indicating that there were no problems and the test was successful. If a problem is detected during the test, an error code is displayed upon completion of the test. For example Code 1 would indicate a problem with the display. If multiple errors are detected, multiple code numbers are displayed. For example, Codes 4, 2, 1, would indicate problems detected with the buttons, LCD contrast, LCD backlight on the control panel. The following lists the control panel self test error codes. Error Code Table Error Code Code Code Code 0 1 2 Description PASS - The control no problems LCD backlight LCD contrast panel has C ode 4 Switch (buttons) Code 5 UART loopback test Resetting the System Fuses The SunTouch Power Center provides two resettable fuses to protect the 18 VAC and 24 VAC circuits. The fuses are located on the front panel of the SunTouch Power Center. Press the fuse button to reset the fuse. See page 40 for fuse locations. SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
Page 1 and 2:
SunTouch ® Pool, Spa and Solar Con
Page 3 and 4:
i Contents IMPORTANT WARNING AND SA
Page 5 and 6:
iii Contents Installing Valve Actua
Page 7 and 8:
v IMPORTANT WARNING AND SAFETY INST
Page 9 and 10:
1 SunTouch ® Control System Overvi
Page 11 and 12:
3 Control Buttons (Continued) ➂
Page 13 and 14:
5 Operating SunTouch in Solar Only
Page 15 and 16:
7 Solar Only Menus (Continued) Syst
Page 17 and 18:
9 Freeze Protection in Solar Only m
Page 19 and 20:
11 SunTouch Main Status Screen (Poo
Page 21 and 22:
13 Pool/Spa Mode Menus The followin
Page 23 and 24:
15 Heat Menu (2/14) (Continued) Spa
Page 25 and 26: 17 Schedules Menu (4/14) Scheduled
Page 27 and 28: 19 Clock Menu (5/14) Use the Clock
Page 29 and 30: 21 Valves Menu (7/14) The valves fe
Page 31 and 32: 23 Advanced Menu (8/14): Calibrate
Page 33 and 34: 25 Advanced Menu (8/14): Reset Fact
Page 35 and 36: 27 SunTouch Solar, Pool and Spa Con
Page 37 and 38: 29 To select a single-speed pump. M
Page 39 and 40: 31 Pump Menu (12/14) (Continued) In
Page 45 and 46: 37 IntelliChlor Menu (13/14): Statu
Page 47 and 48: 39 SunTouch Main Status Screen (Poo
Page 49 and 50: 41 Pool/Spa Mode (Single Body of Wa
Page 51 and 52: 43 SunTouch Solar Package Contents
Page 53 and 54: 45 SunTouch Power Center (Front Vie
Page 55 and 56: 47 8 9 Plumb the solar feed and ret
Page 57 and 58: 49 SunTouch Power Center High Volta
Page 59 and 60: 51 Preparing the SunTouch Power Cen
Page 61 and 62: 53 Removing Electrical Conduit Knoc
Page 63 and 64: 55 Transformer Connections High Vol
Page 65 and 66: 57 Accessing the SunTouch Motherboa
Page 67 and 68: 59 Installing relays (Continued) St
Page 69 and 70: 61 Installing and Connecting Temper
Page 71 and 72: 63 Connecting to a Sta-Rite ® Gas
Page 73 and 74: 65 SunTouch Pool/Spa Controller Sys
Page 75: 67 Connecting IntelliChem to the Su
Page 79 and 80: 71 Temperature vs. Resistance Data
Page 81 and 82: 73 SunTouch Solar, Pool and Spa Con
Page 83 and 84: 75 Wiring SunTouch to the IntelliCh
Page 85 and 86: 77 Wiring IntellilChlor (SCG) and I
Page 87 and 88: 79 Installing the ESO Circuit Board
Page 89 and 90: 81 Commercial Application using ESO
Page 91 and 92: How to BACKWASH Your Filter When yo
show all

SunTouch® - Pentair

Create successful ePaper yourself

Delete template?

Save as template?