SunTouch® - Pentair
SunTouch® - Pentair
SunTouch® - Pentair
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
66<br />
Setting up the SunTouch System for the First Time<br />
(after equipment installation)<br />
Use the following steps if you are setting up the SunTouch system for the first time. Note: The following<br />
setup steps assume that the SunTouch enclosure is installed at the equipment pad and ready for<br />
operation. The recommended first time installation steps for the SunTouch system are:<br />
1. Set the system mode and type (page 24)<br />
System Mode: Configure the SunTouch system to operate in Solar Only or Pool/Spa mode.<br />
System Type: Configure the SunTouch system to operate as a Shared Equipment system or as a Single Body<br />
system (pool only or spa only).<br />
2. Set the system date and time: Solar only (page 6). For Pool/Spa mode (page 9)<br />
Set the system time for Solar Only and time and date for Pool/Spa mode.<br />
3. Assign a circuit function to a circuit name in Pool/Spa mode (see page 26)<br />
Assign Circuit Functions (menu 10/14) to circuits. From the Circuit Type menu, you can assign special logic to<br />
a circuit by selecting one of the available circuit functions. If an auxiliary circuit (AUX) is assigned GENERIC<br />
(simple ON/OFF when the button is pushed) then nothing needs to be done.<br />
4. Configure valve actuators (controlled by AUX circuit) in Pool/Spa mode (see page 21)<br />
The SunTouch system can drive two auxiliary valve actuators for applications such as solar heating and water<br />
features. Assign which circuits will activate valves A (intake) and B (return). Auxiliary valve actuators can be<br />
controlled by any AUX circuit. Valve C is automatically assigned to solar if Solar is enabled in the “Solar”<br />
menu.<br />
5. Set up optional equipment, solar, two-speed pump in Pool/Spa mode (see page 29, 30)<br />
Set up additional equipment such as solar, 2-speed pump, and optional equipment if required. Access the Main<br />
Menus (1/14) to setup optional equipment such as the IntelliFlo VS and IntelliFlo VF pump and IntelliChlor<br />
chlorine generator (see page 33 and 79). To configure SunTouch for special equipment:<br />
• Is solar heating available? Is solar being used for a heat pump?<br />
• What circuits will turn 2-Speed pumps to High Speed?<br />
• Cool-down cycle for the heater - Lets you set circuits that switch the filter pump to high speed.<br />
• Do you want to delay turning off the filter pump for 10 minutes when the heater is turned off?<br />
• Do you want the spa to heat whenever the Spa button is pressed?<br />
CAUTION: When using the IntelliChlor salt chlorine generator and the IntelliFlo with the SunTouch<br />
system, the IntelliChlor power center AC power wires must be connected to the PUMP SIDE OF THE<br />
RELAY located in the SunTouch power center. This ensures that IntelliChlor produces chlorine only<br />
when the main filter pump is on. See page 79 for details.<br />
6. Configuring the heater system options Pool/Spa mode (page 14)<br />
Set the type of heat source being used (Heater, Solar, Solar Preferred).<br />
7. Configure the QuickTouch wireless remote buttons (page 28)<br />
Assign four circuits to the QuickTouch remote buttons. Once you have checked that all buttons operate<br />
properly, place labels on remote buttons.<br />
8. Schedule on/off times for circuit (page 17)<br />
Set times for automatic circuit activation. Up to 6 total programs can be created for all circuits combined.<br />
One circuit can have up to a maximum of 4 programs (4/4). All user created programs are active all the time;<br />
so check that there are not conflicting automated times.<br />
SunTouch Solar, Pool and Spa Control System Installation and User’s Guide